Department of Mechanical Engineering

Research Output 1979 2020

Filter
Paper
Paper

Effect of CFRP inter laminar shear strength by SPWC method

Miura, T., Tabuchi, D., Sajima, T., Doi, T. & Ohnishi, O., Dec 1 2011.

Research output: Contribution to conferencePaper

Carbon fiber reinforced plastics
Shear strength
Aluminum
Volume fraction
Temperature

Effect of chevron angle on condensation heat transfer of HFC134a at high reduced pressures in plate heat exchangers

Miyata, K., Yanagihara, S., Watanabe, N., Mori, H., Hamamoto, Y., Umezawa, S. & Sugita, K., Jan 1 2018.

Research output: Contribution to conferencePaper

heat exchangers
Heat exchangers
Condensation
heat transfer coefficients
condensation

Effect of fullerene poly-hydroxide on Cu-CMP process

Kishida, H., Hayashi, T., Takaya, Y., Kokubo, K. & Suzuki, K., Dec 1 2009.

Research output: Contribution to conferencePaper

Fullerenes
Copper
Abrasives
Hydrogen peroxide
Molecules

Effect of gas flow on the temperature rise of a micro-beam-type thermal conductivity detector

Takamatsu, H., Hisada, K., Fukunaga, T. & Kurata, K., Jan 1 2013.

Research output: Contribution to conferencePaper

Flow of gases
Thermal conductivity
Detectors
Sensors
Temperature

Effect of inlet nozzle shape on performance of darrieus-type hydro-turbine operated in small open water channel

Kazuhiko, N., Daisuke, M., Watanabe, S., Tsuda, S. & Akinori, F., Jan 1 2015.

Research output: Contribution to conferencePaper

Aquaporins
Nozzles
Turbines
Water
Open channel flow
34 Citations (Scopus)

Effect of tip clearance on stall evolution process in a low-speed axial compressor stage

Inoue, M., Yoshida, S., Yamada, K., Kuroumaru, M., Minami, T. & Furukawa, M., Dec 22 2004, p. 385-394. 10 p.

Research output: Contribution to conferencePaper

Compressors
Vortex flow
Rotors
Tornadoes
Flow simulation
1 Citation (Scopus)

Effects of dissolved gas on unsteady cavitating flow around a clark y-11.7% hydrofoil

Daido, H., Watanabe, S. & Tsuda, S., Jan 1 2015.

Research output: Contribution to conferencePaper

Hydrofoils
Unsteady flow
Gases
Drag
Cavitation

Effects of overall equivalence ratio of premixed spray on flame structure of spray jet with a low-volatility fuel

Mikami, M., Nakamoto, K., Kojima, N. & Moriue, O., Jan 1 2007.

Research output: Contribution to conferencePaper

volatility
sprayers
equivalence
flames
Flow rate

Effects of oxygen enrichment on combustion instability under super lean and high EGR conditions

Kawasoe, Y., Harada, K., Hashimoto, H., Moriue, O. & Murase, E., Jan 1 2017.

Research output: Contribution to conferencePaper

Oxygen
Strain rate
Fuel burners
Ignition
Engines

Effects of oxygen enrichment on pulsed flame jet ignition

Nishimura, Y., Moriue, O., Kubo, M., Hotta, I. & Murase, E., Jan 1 2007.

Research output: Contribution to conferencePaper

combustion chambers
Combustion chambers
ignition
Ignition
igniters

Emission Spectroscopy of the C2 swan bands to estimate temperature of the near-extinction flamelets of turbulent premixed flames

Kawasoe, Y., Hashimoto, H., Moriue, O., Murase, E. & Furukawa, J., Jan 1 2017.

Research output: Contribution to conferencePaper

Swan bands
turbulent flames
premixed flames
Emission spectroscopy
extinction

Engineering approach to irreversible electroporation

Takamatsu, H. & Kurata, K., Jan 1 2014.

Research output: Contribution to conferencePaper

engineering
Tissue
Electrodes
electrodes
Tissue regeneration
Thermal energy
Energy storage
Thermal conductivity
Phase change materials
Composite materials
27 Citations (Scopus)

Enhancement of combustion by injection of radicals

Murase, E. & Hanada, K., Dec 1 2000.

Research output: Contribution to conferencePaper

Ignition systems
Fluorescence
Fuel economy
Orifices
Internal combustion engines
1 Citation (Scopus)
Hydrogen
Composite materials
Gases
Carbon black
Cracks
2 Citations (Scopus)

Evaluation of unstable behavior in micro-probe trapped by optical radiation pressure

Kobayashi, M., Hayashi, T. & Takaya, Y., Dec 1 2009.

Research output: Contribution to conferencePaper

Coordinate measuring machines
Radiation
Lasers

Existence of feedbacks from sensing to action for stable grasping and dextrous manipulation by multi-fingered robot hands

Arimoto, S., Tahara, K. & Yamaguchi, M., Dec 1 2001, p. 524-529. 6 p.

Research output: Contribution to conferencePaper

Sensory feedback
End effectors
Robots
Feedback
Actuators
1 Citation (Scopus)

Experiment on condensation heat transfer of HFC134a in a horizontal single rectangular mini-channel

Matsumoto, T., Arata, Y., Miyata, K., Hamamoto, Y. & Mori, H., Jan 1 2018.

Research output: Contribution to conferencePaper

Condensation
condensation
heat transfer
Flow rate
Heat transfer
21 Citations (Scopus)

Feedback control for wire-suspended mechanism with exact linearization

Yanai, N., Yamamoto, M. & Mohri, A., Jan 1 2002, p. 2213-2218. 6 p.

Research output: Contribution to conferencePaper

Linearization
Feedback control
Wire
Cranes
Experiments

Flame propagation into lean region in stratified mixture

Kitagawa, T., Kido, H., Kim, K. S. & Fujioka, K., Dec 1 2002. 1 p.

Research output: Contribution to conferencePaper

Ignition
Butane
Soot
Engines
Flammability

Flame-spread behavior of fuel-droplet arrays with uneven inter-droplet distance

Oyagi, H., Moriue, O., Mikami, M. & Kojima, N., Dec 1 2005, p. 213-216. 4 p.

Research output: Contribution to conferencePaper

Fibers
decane
3 Citations (Scopus)

Friction compensation of the electromechanical drive systems using neural networks

Kiguchi, K., Henrichfreise, H. & Hesseler, K. P., Dec 1 2004, p. 1758-1762. 5 p.

Research output: Contribution to conferencePaper

Friction
Neural networks
Stick-slip
Mechatronics
Position control

FUNDAMENTAL STUDIES ON DIRECT INJECTION STRATIFIED CHARGE COMBUSTION IN A CONSTANT VOLUME BOMB.

Kido, H., Nakashima, K., Kitagawa, T. & Nishino, M., Jan 1 1987, p. 205-212. 8 p.

Research output: Contribution to conferencePaper

Direct injection
Hydrocarbons
Ignition systems
Jet fuel
Nitric oxide
5 Citations (Scopus)

Fuzzy behavior-based motion planning for the PUMA robot

Dassanayake, P., Watanabe, K., Kiguchi, K. & Izumi, K., Dec 1 2000, p. 1912-1917. 6 p.

Research output: Contribution to conferencePaper

Motion planning
Manipulators
Robots
Planning
Angular velocity
6 Citations (Scopus)

Fuzzy neural controller for robot manipulator force control

Kiguchi, K. & Fukuda, T., Jan 1 1995, p. 869-874. 6 p.

Research output: Contribution to conferencePaper

Robot Manipulator
Force Control
Force control
Manipulators
Robots

Generalization of lubricating and sealing performance using dimensionless parameters on low-friction and zero-leakage mechanical seals

Tokunaga, Y., Inoue, H. & Sugimura, J., Jan 1 2018, p. 193-205. 13 p.

Research output: Contribution to conferencePaper

Cavitation
Seals
Load limits
Friction
Reynolds equation
1 Citation (Scopus)

Generation of evaluation function for robot force control using genetic programming

Kiguchi, K., Watanabe, K., Izumi, K. & Fukuda, T., Dec 1 2001, p. 2767-2771. 5 p.

Research output: Contribution to conferencePaper

Robot Control
Force Control
Genetic programming
Function evaluation
Force control
2 Citations (Scopus)
masking
noise reduction
rooms
acoustics
evaluation

Hydrogen absorbing properties and crystal structure of Ti-V-Mn solid solution alloys

Nakamura, Y. & Akiba, E., Jan 1 2002, p. 109-120. 12 p.

Research output: Contribution to conferencePaper

Hydrides
Hydrogen
Solid solutions
solid solutions
Crystal structure

Hydrogen induced strain localization in Al-Zn-Mg-Cu aluminum alloys

Su, H., Toda, H., Masunaga, R., Uesugi, K., Takeuchi, A. & Watanabe, Y., Jan 1 2017, p. 710-711. 2 p.

Research output: Contribution to conferencePaper

Aluminum alloys
Hydrogen
Hydrogen embrittlement
Crack tips
Tomography
5 Citations (Scopus)

Influence of RTA parameters on residual stress and stress gradient of multilayered LPCVD polysilicon film

Yoshikawa, E., Tsugai, M., Horikawa, M., Otani, H. & Hamada, S., Jan 1 2002, p. 451-454. 4 p.

Research output: Contribution to conferencePaper

Rapid thermal annealing
Polysilicon
Residual stresses
Nitrides
Spectroscopy

In-process tool flank wear detection in intermittent cutting process by face milling

Murata, M., Kurokawa, S., Ohnishi, O., Uneda, M. & Doi, T., Dec 1 2011.

Research output: Contribution to conferencePaper

Milling (machining)
Wear of materials
Electromotive force
Electric currents
Contact resistance
2 Citations (Scopus)

In-process tool wear detection of square end mill based on DC two terminal method

Gouarir, A., Kurokawa, S., Murata, M., Sajima, T. & Torii, T., Oct 18 2015.

Research output: Contribution to conferencePaper

Wear of materials
Contact resistance
Electromotive force
Acoustic impedance
Experiments

Intelligent control of a 7-DOF manipulator based on model primitives

Nanayakkara, D. P. T., Watanabe, K., Kiguchi, K. & Shadmehr, R., Dec 1 2002, p. 538-543. 6 p.

Research output: Contribution to conferencePaper

Intelligent Control
Intelligent control
Manipulator
Manipulators
Industrial manipulators

Large-eddy simulation of coal combustion on a pulverized coal combustion test furnace with a practical swirl burner

Watanabe, H., Tanno, K., Baba, Y., Kurose, R. & Komori, S., Jan 1 2009.

Research output: Contribution to conferencePaper

Coal combustion
Large eddy simulation
Fuel burners
Furnaces
Experiments

Large-scale numerical simulation of unsteady flow field in a half-ducted propeller fan using lattice Boltzmann method

Yamada, K., Kusano, K. & Furukawa, M., Jan 1 2015.

Research output: Contribution to conferencePaper

Acoustic fields
Propellers
Unsteady flow
Fans
Flow fields

Lithium ion conductive polymer electrolytes by side group rotation(II)

Satou, A., Nishimura, S., Urabe, S., Yamamoto, H. & Ueyama, N., Dec 1 2005. 1 p.

Research output: Contribution to conferencePaper

Lithium
Ionic conductivity
Electrolytes
Ions
Polymers

Lithium ion conductive polymer electrolytes by side group rotation(III)

Satou, A., Nishimura, S., Urabe, S., Yamamoto, H. & Ueyama, N., Dec 1 2005. 1 p.

Research output: Contribution to conferencePaper

Ionic conductivity
Lithium
Electrolytes
Homopolymerization
Ions

Lithium ion conductive polymer electrolytes by side group rotation - Effects on the conductivity by copolymerization with various monomers-

Sato, A., Nishimura, S., Kono, K., Tabata, D. & Yamamoto, H., Dec 1 2006, p. 4671-4672. 2 p.

Research output: Contribution to conferencePaper

Copolymerization
Lithium
Ionic conductivity
Monomers
Electrolytes
12 Citations (Scopus)

Long-life micro-laser encoder

Sawada, R., Higurashi, E., Ohguchi, O. & Jin, Y., Jan 1 2000, p. 491-495. 5 p.

Research output: Contribution to conferencePaper

Optical waveguides
Photodiodes
Polyimides
Semiconductor lasers
Silicon

Measurement of effective stress intensity factor range of mode II fatigue crack growth using hysteresis loop

Hamada, S. & Liu, M., Jan 1 2013, p. 1717-1723. 7 p.

Research output: Contribution to conferencePaper

Hysteresis loops
effective stress
Fatigue crack propagation
hysteresis
fatigue

Measurement of vapor concentration around an evaporating fuel droplet by infrared absorption technique

Moriue, O., Wendt, C., Eigenbrod, C. & Rath, H. J., Dec 1 2002. 1 p.

Research output: Contribution to conferencePaper

Infrared absorption
Vapors
Microgravity
Radiators
Towers
8 Citations (Scopus)

Measurements of axial and radial thrust forces working on a three-stages centrifugal pump rotor

Yamashita, T., Watanabe, S., Hara, Y., Watanabe, H. & Miyagawa, K., Jan 1 2015.

Research output: Contribution to conferencePaper

Centrifugal pumps
Rotors
Flow rate
Ball bearings
Journal bearings
6 Citations (Scopus)

MEASUREMENTS OF SPATIAL SCALES AND A MODEL FOR SMALL-SCALE STRUCTURE OF TURBULENCE IN AN INTERNAL COMBUSTION ENGINE.

Kido, H., Wakuri, Y. & Murase, E., Jan 1 1983, p. 191-198. 8 p.

Research output: Contribution to conferencePaper

Internal combustion engines
Turbulence

Measurement technique for unsteady low-speed flow fields using poly(TMSP)-based pressure sensitive paint

Mori, H., Maeda, K., Furukawa, M. & Akiyoshi, M., Jan 1 2015.

Research output: Contribution to conferencePaper

Paint
Flow fields
Polymers
Oxygen
Quenching

Method to analyze the spatial current distribution in an operating PEFC based on NMR mesurement using small planer surface coils

Ogawa, K., Yokouchi, Y., Haishi, T. & Ito, K., Jan 1 2014.

Research output: Contribution to conferencePaper

current distribution
fuel cells
Fuel cells
coils
Electrolytes
16 Citations (Scopus)

Micro IC probe for LSI testing

Ito, T., Sawada, R. & Higurashi, E., Jan 1 1999, p. 263-266. 4 p.

Research output: Contribution to conferencePaper

Micromachining
Testing
Contact resistance
Costs
Compliance

Model-based active noise control for two-dimensional closed space by concentrated mass model

Hisano, S., Ishikawa, S., Kijimoto, S. & Koba, Y., Jan 1 2017.

Research output: Contribution to conferencePaper

acoustics
dampers
loudspeakers
microphones
feedback control

Modeling on cavitation dynamics in pressure sensitive adhesives

Yamaguchi, T., Koike, K. & Doi, M., Oct 18 2006. 1 p.

Research output: Contribution to conferencePaper

Cavitation
Adhesives
Stress-strain curves

Molecular dynamics simulation study of the adhesion between end-grafted polymer films

Morita, H., Yamada, M., Yamaguchi, T. & Doi, M., Dec 1 2005, p. 3319-3320. 2 p.

Research output: Contribution to conferencePaper

Polymer films
Molecular dynamics
Adhesion
Computer simulation
Polymers