Interface separation phenomenon in Ti-20mol%Al alloy/iron material joints

Yasuhiro Morizono, Yoshikazu Kodama, Takateru Yamamuro, Minoru Nishida

Research output: Contribution to journalArticle

4 Citations (Scopus)

Abstract

Ti-20mol%Al (Ti-20Al, i.e. Ti-12.3mass%Al) alloy was diffusion-bonded to eutectoid steel at 1273 K for 3.6ks in a vacuum. The joint had a space of a few micrometers in thickness between the Ti-20Al alloy and the steel, and several specimens separated near the interface promptly after the bonding treatment. This phenomenon, which is referred to as "interface separation", is known to depend on alloy composition, bonding temperature and holding time. This paper describes the influence of carbon content in iron materials on the interface separation. Four kinds of carbon steels, an alloy steel and a cast iron were used as a mating material for the Ti-20Al alloy. Diffusion bonding was carried out at 1273K for 3.6 ks in a vacuum. The diffusion of constituent elements into each parent material and the formation of reaction phases were observed in the vicinity of the interface in all cases. The interface separation was clearly seen in the joints with the carbon steels and the cast iron containing more than 0.82 mass% C. It was also confirmed that the space formed near the interface spread to the iron material side. On the other hand, the bonding of the Ti-20Al alloy to the alloy steel with high carbon content was achieved without incident. In this joint, the diffusion of Fe into the Ti-20Al side was inhibited by TiC layer formed at the interface. The mechanism of the interface separation is discussed from the viewpoint of thermal stress, reaction phase and diffusion behavior.

Original languageEnglish
Pages (from-to)251-257
Number of pages7
JournalTetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan
Volume94
Issue number7
DOIs
Publication statusPublished - Dec 1 2008

Fingerprint

iron alloys
Iron alloys
Alloy steel
Carbon steel
Cast iron
steels
iron
Carbon
Iron
Vacuum
carbon steels
Diffusion bonding
Steel
casts
Thermal stress
diffusion welding
vacuum
carbon
thermal stresses
micrometers

All Science Journal Classification (ASJC) codes

  • Materials Chemistry
  • Metals and Alloys
  • Condensed Matter Physics
  • Physical and Theoretical Chemistry

Cite this

Interface separation phenomenon in Ti-20mol%Al alloy/iron material joints. / Morizono, Yasuhiro; Kodama, Yoshikazu; Yamamuro, Takateru; Nishida, Minoru.

In: Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan, Vol. 94, No. 7, 01.12.2008, p. 251-257.

Research output: Contribution to journalArticle

Morizono, Yasuhiro ; Kodama, Yoshikazu ; Yamamuro, Takateru ; Nishida, Minoru. / Interface separation phenomenon in Ti-20mol%Al alloy/iron material joints. In: Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan. 2008 ; Vol. 94, No. 7. pp. 251-257.
@article{d848953dd41a47de97dfbfa354d06f7f,
title = "Interface separation phenomenon in Ti-20mol{\%}Al alloy/iron material joints",
abstract = "Ti-20mol{\%}Al (Ti-20Al, i.e. Ti-12.3mass{\%}Al) alloy was diffusion-bonded to eutectoid steel at 1273 K for 3.6ks in a vacuum. The joint had a space of a few micrometers in thickness between the Ti-20Al alloy and the steel, and several specimens separated near the interface promptly after the bonding treatment. This phenomenon, which is referred to as {"}interface separation{"}, is known to depend on alloy composition, bonding temperature and holding time. This paper describes the influence of carbon content in iron materials on the interface separation. Four kinds of carbon steels, an alloy steel and a cast iron were used as a mating material for the Ti-20Al alloy. Diffusion bonding was carried out at 1273K for 3.6 ks in a vacuum. The diffusion of constituent elements into each parent material and the formation of reaction phases were observed in the vicinity of the interface in all cases. The interface separation was clearly seen in the joints with the carbon steels and the cast iron containing more than 0.82 mass{\%} C. It was also confirmed that the space formed near the interface spread to the iron material side. On the other hand, the bonding of the Ti-20Al alloy to the alloy steel with high carbon content was achieved without incident. In this joint, the diffusion of Fe into the Ti-20Al side was inhibited by TiC layer formed at the interface. The mechanism of the interface separation is discussed from the viewpoint of thermal stress, reaction phase and diffusion behavior.",
author = "Yasuhiro Morizono and Yoshikazu Kodama and Takateru Yamamuro and Minoru Nishida",
year = "2008",
month = "12",
day = "1",
doi = "10.2355/tetsutohagane.94.251",
language = "English",
volume = "94",
pages = "251--257",
journal = "Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan",
issn = "0021-1575",
publisher = "一般社団法人 日本鉄鋼協会",
number = "7",

}

TY - JOUR

T1 - Interface separation phenomenon in Ti-20mol%Al alloy/iron material joints

AU - Morizono, Yasuhiro

AU - Kodama, Yoshikazu

AU - Yamamuro, Takateru

AU - Nishida, Minoru

PY - 2008/12/1

Y1 - 2008/12/1

N2 - Ti-20mol%Al (Ti-20Al, i.e. Ti-12.3mass%Al) alloy was diffusion-bonded to eutectoid steel at 1273 K for 3.6ks in a vacuum. The joint had a space of a few micrometers in thickness between the Ti-20Al alloy and the steel, and several specimens separated near the interface promptly after the bonding treatment. This phenomenon, which is referred to as "interface separation", is known to depend on alloy composition, bonding temperature and holding time. This paper describes the influence of carbon content in iron materials on the interface separation. Four kinds of carbon steels, an alloy steel and a cast iron were used as a mating material for the Ti-20Al alloy. Diffusion bonding was carried out at 1273K for 3.6 ks in a vacuum. The diffusion of constituent elements into each parent material and the formation of reaction phases were observed in the vicinity of the interface in all cases. The interface separation was clearly seen in the joints with the carbon steels and the cast iron containing more than 0.82 mass% C. It was also confirmed that the space formed near the interface spread to the iron material side. On the other hand, the bonding of the Ti-20Al alloy to the alloy steel with high carbon content was achieved without incident. In this joint, the diffusion of Fe into the Ti-20Al side was inhibited by TiC layer formed at the interface. The mechanism of the interface separation is discussed from the viewpoint of thermal stress, reaction phase and diffusion behavior.

AB - Ti-20mol%Al (Ti-20Al, i.e. Ti-12.3mass%Al) alloy was diffusion-bonded to eutectoid steel at 1273 K for 3.6ks in a vacuum. The joint had a space of a few micrometers in thickness between the Ti-20Al alloy and the steel, and several specimens separated near the interface promptly after the bonding treatment. This phenomenon, which is referred to as "interface separation", is known to depend on alloy composition, bonding temperature and holding time. This paper describes the influence of carbon content in iron materials on the interface separation. Four kinds of carbon steels, an alloy steel and a cast iron were used as a mating material for the Ti-20Al alloy. Diffusion bonding was carried out at 1273K for 3.6 ks in a vacuum. The diffusion of constituent elements into each parent material and the formation of reaction phases were observed in the vicinity of the interface in all cases. The interface separation was clearly seen in the joints with the carbon steels and the cast iron containing more than 0.82 mass% C. It was also confirmed that the space formed near the interface spread to the iron material side. On the other hand, the bonding of the Ti-20Al alloy to the alloy steel with high carbon content was achieved without incident. In this joint, the diffusion of Fe into the Ti-20Al side was inhibited by TiC layer formed at the interface. The mechanism of the interface separation is discussed from the viewpoint of thermal stress, reaction phase and diffusion behavior.

UR - http://www.scopus.com/inward/record.url?scp=70449564603&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=70449564603&partnerID=8YFLogxK

U2 - 10.2355/tetsutohagane.94.251

DO - 10.2355/tetsutohagane.94.251

M3 - Article

AN - SCOPUS:70449564603

VL - 94

SP - 251

EP - 257

JO - Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan

JF - Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan

SN - 0021-1575

IS - 7

ER -