Mechanical properties of a spray-cast aluminum alloy processed by severe plastic deformation

Cheng Xu, Megumi Kawasaki, Minoru Furukawa, Zenji Horita, Terence G. Langdon

Research output: Chapter in Book/Report/Conference proceedingConference contribution

1 Citation (Scopus)

Abstract

Experiments were conducted to evaluate the mechanical properties of a spray-cast Al-7034 alloy processed by severe plastic deformation. The alloy was received with an average grain size of ∼2.1 μm and processed by equal-channel angular pressing (ECAP) at a temperature of 473 K to give a grain size of ∼0.3 μm after 6 or 8 passes. Following ECAP, the mechanical properties were evaluated at room temperature (298 K) and at an elevated temperature of 673 K. In tensile testing at ambient temperature, the stress-strain curves show very short regions of strain hardening after ECAP and low values for the ultimate tensile strength by comparison with the unpressed alloy. This lack of strength is due to the high pressures imposed by ECAP and the consequent fragmentation and dissolution of the rod-like MgZn2 precipitates. It is shown that the strength may be restored by performing an appropriate ageing treatment after ECAP. Superplastic ductilities were recorded at a temperature of 673 K with tensile elongations exceeding 1000%. Careful inspection of the polished surfaces of samples pulled to fracture in the superplastic condition revealed the occurrence of extensive internal cavitation. Quantitative measurements showed the development of these internal cavities is consistent with conventional superplastic alloys.

Original languageEnglish
Title of host publicationSupplement to THERMEC 2006, 5th International Conference on PROCESSING and MANUFACTURING OF ADVANCED MATERIALS, THERMEC 2006
Pages141-148
Number of pages8
EditionPART 1
Publication statusPublished - Dec 1 2007
Event5th International Conference on Processing and Manufacturing of Advanced Materials - THERMEC'2006 - Vancouver, Canada
Duration: Jul 4 2006Jul 8 2006

Publication series

NameMaterials Science Forum
NumberPART 1
Volume539-543
ISSN (Print)0255-5476

Other

Other5th International Conference on Processing and Manufacturing of Advanced Materials - THERMEC'2006
CountryCanada
CityVancouver
Period7/4/067/8/06

Fingerprint

Equal channel angular pressing
cast alloys
pressing
aluminum alloys
plastic deformation
sprayers
Aluminum alloys
Plastic deformation
mechanical properties
Mechanical properties
Temperature
grain size
strain hardening
Tensile testing
Stress-strain curves
cavitation flow
ductility
Strain hardening
Cavitation
tensile strength

All Science Journal Classification (ASJC) codes

  • Materials Science(all)
  • Condensed Matter Physics
  • Mechanics of Materials
  • Mechanical Engineering

Cite this

Xu, C., Kawasaki, M., Furukawa, M., Horita, Z., & Langdon, T. G. (2007). Mechanical properties of a spray-cast aluminum alloy processed by severe plastic deformation. In Supplement to THERMEC 2006, 5th International Conference on PROCESSING and MANUFACTURING OF ADVANCED MATERIALS, THERMEC 2006 (PART 1 ed., pp. 141-148). (Materials Science Forum; Vol. 539-543, No. PART 1).

Mechanical properties of a spray-cast aluminum alloy processed by severe plastic deformation. / Xu, Cheng; Kawasaki, Megumi; Furukawa, Minoru; Horita, Zenji; Langdon, Terence G.

Supplement to THERMEC 2006, 5th International Conference on PROCESSING and MANUFACTURING OF ADVANCED MATERIALS, THERMEC 2006. PART 1. ed. 2007. p. 141-148 (Materials Science Forum; Vol. 539-543, No. PART 1).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Xu, C, Kawasaki, M, Furukawa, M, Horita, Z & Langdon, TG 2007, Mechanical properties of a spray-cast aluminum alloy processed by severe plastic deformation. in Supplement to THERMEC 2006, 5th International Conference on PROCESSING and MANUFACTURING OF ADVANCED MATERIALS, THERMEC 2006. PART 1 edn, Materials Science Forum, no. PART 1, vol. 539-543, pp. 141-148, 5th International Conference on Processing and Manufacturing of Advanced Materials - THERMEC'2006, Vancouver, Canada, 7/4/06.
Xu C, Kawasaki M, Furukawa M, Horita Z, Langdon TG. Mechanical properties of a spray-cast aluminum alloy processed by severe plastic deformation. In Supplement to THERMEC 2006, 5th International Conference on PROCESSING and MANUFACTURING OF ADVANCED MATERIALS, THERMEC 2006. PART 1 ed. 2007. p. 141-148. (Materials Science Forum; PART 1).
Xu, Cheng ; Kawasaki, Megumi ; Furukawa, Minoru ; Horita, Zenji ; Langdon, Terence G. / Mechanical properties of a spray-cast aluminum alloy processed by severe plastic deformation. Supplement to THERMEC 2006, 5th International Conference on PROCESSING and MANUFACTURING OF ADVANCED MATERIALS, THERMEC 2006. PART 1. ed. 2007. pp. 141-148 (Materials Science Forum; PART 1).
@inproceedings{97d7274f43ed4fec8b5fd58308c47923,
title = "Mechanical properties of a spray-cast aluminum alloy processed by severe plastic deformation",
abstract = "Experiments were conducted to evaluate the mechanical properties of a spray-cast Al-7034 alloy processed by severe plastic deformation. The alloy was received with an average grain size of ∼2.1 μm and processed by equal-channel angular pressing (ECAP) at a temperature of 473 K to give a grain size of ∼0.3 μm after 6 or 8 passes. Following ECAP, the mechanical properties were evaluated at room temperature (298 K) and at an elevated temperature of 673 K. In tensile testing at ambient temperature, the stress-strain curves show very short regions of strain hardening after ECAP and low values for the ultimate tensile strength by comparison with the unpressed alloy. This lack of strength is due to the high pressures imposed by ECAP and the consequent fragmentation and dissolution of the rod-like MgZn2 precipitates. It is shown that the strength may be restored by performing an appropriate ageing treatment after ECAP. Superplastic ductilities were recorded at a temperature of 673 K with tensile elongations exceeding 1000{\%}. Careful inspection of the polished surfaces of samples pulled to fracture in the superplastic condition revealed the occurrence of extensive internal cavitation. Quantitative measurements showed the development of these internal cavities is consistent with conventional superplastic alloys.",
author = "Cheng Xu and Megumi Kawasaki and Minoru Furukawa and Zenji Horita and Langdon, {Terence G.}",
year = "2007",
month = "12",
day = "1",
language = "English",
isbn = "0878494286",
series = "Materials Science Forum",
number = "PART 1",
pages = "141--148",
booktitle = "Supplement to THERMEC 2006, 5th International Conference on PROCESSING and MANUFACTURING OF ADVANCED MATERIALS, THERMEC 2006",
edition = "PART 1",

}

TY - GEN

T1 - Mechanical properties of a spray-cast aluminum alloy processed by severe plastic deformation

AU - Xu, Cheng

AU - Kawasaki, Megumi

AU - Furukawa, Minoru

AU - Horita, Zenji

AU - Langdon, Terence G.

PY - 2007/12/1

Y1 - 2007/12/1

N2 - Experiments were conducted to evaluate the mechanical properties of a spray-cast Al-7034 alloy processed by severe plastic deformation. The alloy was received with an average grain size of ∼2.1 μm and processed by equal-channel angular pressing (ECAP) at a temperature of 473 K to give a grain size of ∼0.3 μm after 6 or 8 passes. Following ECAP, the mechanical properties were evaluated at room temperature (298 K) and at an elevated temperature of 673 K. In tensile testing at ambient temperature, the stress-strain curves show very short regions of strain hardening after ECAP and low values for the ultimate tensile strength by comparison with the unpressed alloy. This lack of strength is due to the high pressures imposed by ECAP and the consequent fragmentation and dissolution of the rod-like MgZn2 precipitates. It is shown that the strength may be restored by performing an appropriate ageing treatment after ECAP. Superplastic ductilities were recorded at a temperature of 673 K with tensile elongations exceeding 1000%. Careful inspection of the polished surfaces of samples pulled to fracture in the superplastic condition revealed the occurrence of extensive internal cavitation. Quantitative measurements showed the development of these internal cavities is consistent with conventional superplastic alloys.

AB - Experiments were conducted to evaluate the mechanical properties of a spray-cast Al-7034 alloy processed by severe plastic deformation. The alloy was received with an average grain size of ∼2.1 μm and processed by equal-channel angular pressing (ECAP) at a temperature of 473 K to give a grain size of ∼0.3 μm after 6 or 8 passes. Following ECAP, the mechanical properties were evaluated at room temperature (298 K) and at an elevated temperature of 673 K. In tensile testing at ambient temperature, the stress-strain curves show very short regions of strain hardening after ECAP and low values for the ultimate tensile strength by comparison with the unpressed alloy. This lack of strength is due to the high pressures imposed by ECAP and the consequent fragmentation and dissolution of the rod-like MgZn2 precipitates. It is shown that the strength may be restored by performing an appropriate ageing treatment after ECAP. Superplastic ductilities were recorded at a temperature of 673 K with tensile elongations exceeding 1000%. Careful inspection of the polished surfaces of samples pulled to fracture in the superplastic condition revealed the occurrence of extensive internal cavitation. Quantitative measurements showed the development of these internal cavities is consistent with conventional superplastic alloys.

UR - http://www.scopus.com/inward/record.url?scp=38349011600&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=38349011600&partnerID=8YFLogxK

M3 - Conference contribution

AN - SCOPUS:38349011600

SN - 0878494286

SN - 9780878494286

T3 - Materials Science Forum

SP - 141

EP - 148

BT - Supplement to THERMEC 2006, 5th International Conference on PROCESSING and MANUFACTURING OF ADVANCED MATERIALS, THERMEC 2006

ER -