Tentative study on performance of darriues-type hydroturbine operated in small open water channel

D. Matsushita, R. Moriyama, K. Nakashima, Satoshi Watanabe, K. Okuma, A. Furukawa

Research output: Contribution to journalConference article

1 Citation (Scopus)

Abstract

The development of small hydropower is one of the realistic and preferable utilizations of renewable energy, but the extra-low head hydropower less than 2 m is almost undeveloped yet for some reasons. The authors have developed several types of Darrieus-type hydro-turbine system, and among them, the Darrieus-turbine with a wear and a nozzle installed upstream of turbine is so far in success to obtain more output power, i.e. more shaft torque, by gathering all water into the turbine. However, there can several cases exist, in which installing the wear covering all the flow channel width is unrealistic. Then, in the present study, the hydraulic performances of Darrieus-type hydro-turbine with the inlet nozzle is investigated, putting alone in a small open channel without upstream wear. In the experiment, the five-bladed Darrieus-type runner with the pitch-circle diameter of 300 mm and the blade span of 300 mm is vertically installed in the open channel with the width of 1,200 mm. The effectiveness of the shape of the inlet nozzle is also examined using two types of two-dimensional symmetric nozzle, the straight line nozzle (SL nozzle) with the converging angle of 45 degrees and the half diameter curved nozzle (HD nozzle) whose radius is a half diameter of runner pitch circle. Inlet and outlet nozzle widths are in common for the both nozzles, which are 540 mm and 240 mm respectively. All the experiments are carried out under the conditions with constant flow rate and downstream water level, and performances are evaluated by measured output torque and the measured head difference between the water levels upstream and downstream of the turbine. As a result, it is found that the output power is remarkably increased by installing the inlet nozzle, and the turbine with SL nozzle produces larger power than that with HD nozzle. However, the peak efficiency is deteriorated in both cases. The speed ratio defined by the rotor speed divided by the downstream water velocity at the peak efficiency is larger in both cases with the inlet nozzle, partly due to the increase of inflow velocity into the turbine. In order to understand the cause of the differences of power, i.e. torque characteristics of the turbine with SL and HD nozzles, twodimensional CFD simulation is carried out. It is found that the instantaneous torque variation is important for the overall turbine performances, indicating the possibility of further performance improvement through the optimization of nozzle geometry.

Original languageEnglish
Article number062007
JournalIOP Conference Series: Earth and Environmental Science
Volume22
DOIs
Publication statusPublished - Jan 1 2014
Event27th IAHR Symposium on Hydraulic Machinery and Systems, IAHR 2014 - Montreal, Canada
Duration: Sep 22 2014Sep 26 2014

Fingerprint

open water
turbine
torque
water level
channel flow
shaft
inflow
experiment
hydraulics
geometry
water

All Science Journal Classification (ASJC) codes

  • Environmental Science(all)
  • Earth and Planetary Sciences(all)

Cite this

Tentative study on performance of darriues-type hydroturbine operated in small open water channel. / Matsushita, D.; Moriyama, R.; Nakashima, K.; Watanabe, Satoshi; Okuma, K.; Furukawa, A.

In: IOP Conference Series: Earth and Environmental Science, Vol. 22, 062007, 01.01.2014.

Research output: Contribution to journalConference article

@article{b9133d3ba6bb41a7ad232c0052b2f026,
title = "Tentative study on performance of darriues-type hydroturbine operated in small open water channel",
abstract = "The development of small hydropower is one of the realistic and preferable utilizations of renewable energy, but the extra-low head hydropower less than 2 m is almost undeveloped yet for some reasons. The authors have developed several types of Darrieus-type hydro-turbine system, and among them, the Darrieus-turbine with a wear and a nozzle installed upstream of turbine is so far in success to obtain more output power, i.e. more shaft torque, by gathering all water into the turbine. However, there can several cases exist, in which installing the wear covering all the flow channel width is unrealistic. Then, in the present study, the hydraulic performances of Darrieus-type hydro-turbine with the inlet nozzle is investigated, putting alone in a small open channel without upstream wear. In the experiment, the five-bladed Darrieus-type runner with the pitch-circle diameter of 300 mm and the blade span of 300 mm is vertically installed in the open channel with the width of 1,200 mm. The effectiveness of the shape of the inlet nozzle is also examined using two types of two-dimensional symmetric nozzle, the straight line nozzle (SL nozzle) with the converging angle of 45 degrees and the half diameter curved nozzle (HD nozzle) whose radius is a half diameter of runner pitch circle. Inlet and outlet nozzle widths are in common for the both nozzles, which are 540 mm and 240 mm respectively. All the experiments are carried out under the conditions with constant flow rate and downstream water level, and performances are evaluated by measured output torque and the measured head difference between the water levels upstream and downstream of the turbine. As a result, it is found that the output power is remarkably increased by installing the inlet nozzle, and the turbine with SL nozzle produces larger power than that with HD nozzle. However, the peak efficiency is deteriorated in both cases. The speed ratio defined by the rotor speed divided by the downstream water velocity at the peak efficiency is larger in both cases with the inlet nozzle, partly due to the increase of inflow velocity into the turbine. In order to understand the cause of the differences of power, i.e. torque characteristics of the turbine with SL and HD nozzles, twodimensional CFD simulation is carried out. It is found that the instantaneous torque variation is important for the overall turbine performances, indicating the possibility of further performance improvement through the optimization of nozzle geometry.",
author = "D. Matsushita and R. Moriyama and K. Nakashima and Satoshi Watanabe and K. Okuma and A. Furukawa",
year = "2014",
month = "1",
day = "1",
doi = "10.1088/1755-1315/22/6/062007",
language = "English",
volume = "22",
journal = "IOP Conference Series: Earth and Environmental Science",
issn = "1755-1307",
publisher = "IOP Publishing Ltd.",

}

TY - JOUR

T1 - Tentative study on performance of darriues-type hydroturbine operated in small open water channel

AU - Matsushita, D.

AU - Moriyama, R.

AU - Nakashima, K.

AU - Watanabe, Satoshi

AU - Okuma, K.

AU - Furukawa, A.

PY - 2014/1/1

Y1 - 2014/1/1

N2 - The development of small hydropower is one of the realistic and preferable utilizations of renewable energy, but the extra-low head hydropower less than 2 m is almost undeveloped yet for some reasons. The authors have developed several types of Darrieus-type hydro-turbine system, and among them, the Darrieus-turbine with a wear and a nozzle installed upstream of turbine is so far in success to obtain more output power, i.e. more shaft torque, by gathering all water into the turbine. However, there can several cases exist, in which installing the wear covering all the flow channel width is unrealistic. Then, in the present study, the hydraulic performances of Darrieus-type hydro-turbine with the inlet nozzle is investigated, putting alone in a small open channel without upstream wear. In the experiment, the five-bladed Darrieus-type runner with the pitch-circle diameter of 300 mm and the blade span of 300 mm is vertically installed in the open channel with the width of 1,200 mm. The effectiveness of the shape of the inlet nozzle is also examined using two types of two-dimensional symmetric nozzle, the straight line nozzle (SL nozzle) with the converging angle of 45 degrees and the half diameter curved nozzle (HD nozzle) whose radius is a half diameter of runner pitch circle. Inlet and outlet nozzle widths are in common for the both nozzles, which are 540 mm and 240 mm respectively. All the experiments are carried out under the conditions with constant flow rate and downstream water level, and performances are evaluated by measured output torque and the measured head difference between the water levels upstream and downstream of the turbine. As a result, it is found that the output power is remarkably increased by installing the inlet nozzle, and the turbine with SL nozzle produces larger power than that with HD nozzle. However, the peak efficiency is deteriorated in both cases. The speed ratio defined by the rotor speed divided by the downstream water velocity at the peak efficiency is larger in both cases with the inlet nozzle, partly due to the increase of inflow velocity into the turbine. In order to understand the cause of the differences of power, i.e. torque characteristics of the turbine with SL and HD nozzles, twodimensional CFD simulation is carried out. It is found that the instantaneous torque variation is important for the overall turbine performances, indicating the possibility of further performance improvement through the optimization of nozzle geometry.

AB - The development of small hydropower is one of the realistic and preferable utilizations of renewable energy, but the extra-low head hydropower less than 2 m is almost undeveloped yet for some reasons. The authors have developed several types of Darrieus-type hydro-turbine system, and among them, the Darrieus-turbine with a wear and a nozzle installed upstream of turbine is so far in success to obtain more output power, i.e. more shaft torque, by gathering all water into the turbine. However, there can several cases exist, in which installing the wear covering all the flow channel width is unrealistic. Then, in the present study, the hydraulic performances of Darrieus-type hydro-turbine with the inlet nozzle is investigated, putting alone in a small open channel without upstream wear. In the experiment, the five-bladed Darrieus-type runner with the pitch-circle diameter of 300 mm and the blade span of 300 mm is vertically installed in the open channel with the width of 1,200 mm. The effectiveness of the shape of the inlet nozzle is also examined using two types of two-dimensional symmetric nozzle, the straight line nozzle (SL nozzle) with the converging angle of 45 degrees and the half diameter curved nozzle (HD nozzle) whose radius is a half diameter of runner pitch circle. Inlet and outlet nozzle widths are in common for the both nozzles, which are 540 mm and 240 mm respectively. All the experiments are carried out under the conditions with constant flow rate and downstream water level, and performances are evaluated by measured output torque and the measured head difference between the water levels upstream and downstream of the turbine. As a result, it is found that the output power is remarkably increased by installing the inlet nozzle, and the turbine with SL nozzle produces larger power than that with HD nozzle. However, the peak efficiency is deteriorated in both cases. The speed ratio defined by the rotor speed divided by the downstream water velocity at the peak efficiency is larger in both cases with the inlet nozzle, partly due to the increase of inflow velocity into the turbine. In order to understand the cause of the differences of power, i.e. torque characteristics of the turbine with SL and HD nozzles, twodimensional CFD simulation is carried out. It is found that the instantaneous torque variation is important for the overall turbine performances, indicating the possibility of further performance improvement through the optimization of nozzle geometry.

UR - http://www.scopus.com/inward/record.url?scp=84919632902&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84919632902&partnerID=8YFLogxK

U2 - 10.1088/1755-1315/22/6/062007

DO - 10.1088/1755-1315/22/6/062007

M3 - Conference article

AN - SCOPUS:84919632902

VL - 22

JO - IOP Conference Series: Earth and Environmental Science

JF - IOP Conference Series: Earth and Environmental Science

SN - 1755-1307

M1 - 062007

ER -