Transition of multi-deformation modes in Ti-10Mo alloy with oxygen addition

X. H. Min, S. Emura, K. Tsuchiya, T. Nishimura, K. Tsuzaki

Research output: Contribution to journalArticle

13 Citations (Scopus)

Abstract

Microstructure, crevice corrosion resistance, and tensile deformation mode were investigated in Ti-10Mo- xO alloys (x=0.1, 0.2, 0.3 and 0.4 mass%). Along with a β parent phase, an athermal ω phase was found to be present in each alloy without a significant difference in its diffraction peak within X-ray diffraction profiles. Thermally induced α″ martensite was also observed in the alloy with high oxygen content, implying that the formation of thermally induced α″ martensite was enhanced by increasing oxygen content. All four alloys exhibited a high degree of crevice corrosion resistance within a hot (373. K) chloride-rich highly acidic solution. Room-temperature tensile testing of the alloys, with oxygen content ranging from 0.1 mass% to 0.4 mass%, revealed that tensile strength ranged from 739. MPa to 1035. MPa and that total elongation ranged from 46% to 6%. An examination of deformation microstructures by electron backscattered diffraction indicated that with increasing oxygen content, the deformation mode underwent a transition from stress-induced α″ martensitic transformation to {332}〈113〉 mechanical twinning and further on to dislocation slip, leading to an increase in strength but a decrease in ductility.

Original languageEnglish
Pages (from-to)88-96
Number of pages9
JournalMaterials Science and Engineering A
Volume590
DOIs
Publication statusPublished - Jan 10 2014

Fingerprint

Oxygen
oxygen
martensite
Martensite
corrosion resistance
Corrosion resistance
cracks
mechanical twinning
tensile deformation
microstructure
Microstructure
Twinning
Martensitic transformations
martensitic transformation
Tensile testing
ductility
Dislocations (crystals)
diffraction
Electron diffraction
tensile strength

All Science Journal Classification (ASJC) codes

  • Materials Science(all)
  • Condensed Matter Physics
  • Mechanics of Materials
  • Mechanical Engineering

Cite this

Transition of multi-deformation modes in Ti-10Mo alloy with oxygen addition. / Min, X. H.; Emura, S.; Tsuchiya, K.; Nishimura, T.; Tsuzaki, K.

In: Materials Science and Engineering A, Vol. 590, 10.01.2014, p. 88-96.

Research output: Contribution to journalArticle

Min, X. H. ; Emura, S. ; Tsuchiya, K. ; Nishimura, T. ; Tsuzaki, K. / Transition of multi-deformation modes in Ti-10Mo alloy with oxygen addition. In: Materials Science and Engineering A. 2014 ; Vol. 590. pp. 88-96.
@article{cb00116ac1944131adf2321da513a1e0,
title = "Transition of multi-deformation modes in Ti-10Mo alloy with oxygen addition",
abstract = "Microstructure, crevice corrosion resistance, and tensile deformation mode were investigated in Ti-10Mo- xO alloys (x=0.1, 0.2, 0.3 and 0.4 mass{\%}). Along with a β parent phase, an athermal ω phase was found to be present in each alloy without a significant difference in its diffraction peak within X-ray diffraction profiles. Thermally induced α″ martensite was also observed in the alloy with high oxygen content, implying that the formation of thermally induced α″ martensite was enhanced by increasing oxygen content. All four alloys exhibited a high degree of crevice corrosion resistance within a hot (373. K) chloride-rich highly acidic solution. Room-temperature tensile testing of the alloys, with oxygen content ranging from 0.1 mass{\%} to 0.4 mass{\%}, revealed that tensile strength ranged from 739. MPa to 1035. MPa and that total elongation ranged from 46{\%} to 6{\%}. An examination of deformation microstructures by electron backscattered diffraction indicated that with increasing oxygen content, the deformation mode underwent a transition from stress-induced α″ martensitic transformation to {332}〈113〉 mechanical twinning and further on to dislocation slip, leading to an increase in strength but a decrease in ductility.",
author = "Min, {X. H.} and S. Emura and K. Tsuchiya and T. Nishimura and K. Tsuzaki",
year = "2014",
month = "1",
day = "10",
doi = "10.1016/j.msea.2013.10.010",
language = "English",
volume = "590",
pages = "88--96",
journal = "Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing",
issn = "0921-5093",
publisher = "Elsevier BV",

}

TY - JOUR

T1 - Transition of multi-deformation modes in Ti-10Mo alloy with oxygen addition

AU - Min, X. H.

AU - Emura, S.

AU - Tsuchiya, K.

AU - Nishimura, T.

AU - Tsuzaki, K.

PY - 2014/1/10

Y1 - 2014/1/10

N2 - Microstructure, crevice corrosion resistance, and tensile deformation mode were investigated in Ti-10Mo- xO alloys (x=0.1, 0.2, 0.3 and 0.4 mass%). Along with a β parent phase, an athermal ω phase was found to be present in each alloy without a significant difference in its diffraction peak within X-ray diffraction profiles. Thermally induced α″ martensite was also observed in the alloy with high oxygen content, implying that the formation of thermally induced α″ martensite was enhanced by increasing oxygen content. All four alloys exhibited a high degree of crevice corrosion resistance within a hot (373. K) chloride-rich highly acidic solution. Room-temperature tensile testing of the alloys, with oxygen content ranging from 0.1 mass% to 0.4 mass%, revealed that tensile strength ranged from 739. MPa to 1035. MPa and that total elongation ranged from 46% to 6%. An examination of deformation microstructures by electron backscattered diffraction indicated that with increasing oxygen content, the deformation mode underwent a transition from stress-induced α″ martensitic transformation to {332}〈113〉 mechanical twinning and further on to dislocation slip, leading to an increase in strength but a decrease in ductility.

AB - Microstructure, crevice corrosion resistance, and tensile deformation mode were investigated in Ti-10Mo- xO alloys (x=0.1, 0.2, 0.3 and 0.4 mass%). Along with a β parent phase, an athermal ω phase was found to be present in each alloy without a significant difference in its diffraction peak within X-ray diffraction profiles. Thermally induced α″ martensite was also observed in the alloy with high oxygen content, implying that the formation of thermally induced α″ martensite was enhanced by increasing oxygen content. All four alloys exhibited a high degree of crevice corrosion resistance within a hot (373. K) chloride-rich highly acidic solution. Room-temperature tensile testing of the alloys, with oxygen content ranging from 0.1 mass% to 0.4 mass%, revealed that tensile strength ranged from 739. MPa to 1035. MPa and that total elongation ranged from 46% to 6%. An examination of deformation microstructures by electron backscattered diffraction indicated that with increasing oxygen content, the deformation mode underwent a transition from stress-induced α″ martensitic transformation to {332}〈113〉 mechanical twinning and further on to dislocation slip, leading to an increase in strength but a decrease in ductility.

UR - http://www.scopus.com/inward/record.url?scp=84886731113&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84886731113&partnerID=8YFLogxK

U2 - 10.1016/j.msea.2013.10.010

DO - 10.1016/j.msea.2013.10.010

M3 - Article

AN - SCOPUS:84886731113

VL - 590

SP - 88

EP - 96

JO - Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing

JF - Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing

SN - 0921-5093

ER -