Dislocation characterization by the direct-fitting/modified Williamson–Hall (DF/mWH) method in cold worked ferritic steel

Setsuo Takaki, Takuro Masumura, Toshihiro Tsuchiyma

研究成果: ジャーナルへの寄稿記事

1 引用 (Scopus)

抄録

X-ray diffraction is a powerful tool for dislocation characterization, which includes evaluation of dislocation distribution, nature of dislocation, and dislocation density. In the Williamson–Hall (WH) plots, the full width at half maximum (FWHM) is plotted relative to the diffraction angle for each diffraction peak and the method corresponds to the basic approach for dislocation characterization. However, the elastic anisotropy in each crystal plane makes the analysis of WH plots difficult because elastic anisotropy also affects the FWHM of diffraction peaks. In order to correct the effect of elastic anisotropy, Ungár developed a unique methodology by using the contrast factor C, and this is termed as the modified Williamson–Hall (mWH) method. Conversely, researchers developed a new methodology termed as the “direct-fitting (DF) method,” in which the elastic anisotropy is corrected by directly applying the diffraction Young’s modulus ratio (ω). In the DF method, a linear relation is realized in the corrected WH plots, and reliable values are obtained for the parameter α that contains information on the crystallite size. In the present study, the α-value obtained using the DF method was applied to the mWH equation, and dislocation characterization was performed in a low carbon ferritic steel (Fe-0.0056%C) by cold rolling. The results indicated that increasing the extent of cold rolling decreases the screw component of dislocation, and monotonically increases the parameter φ (which contains the information of dislocation density). Additionally, the parameter A (which depends on the dislocation arrangement) was evaluated at approximately 0.50 for cold worked ferrite.

元の言語英語
ページ(範囲)567-572
ページ数6
ジャーナルisij international
59
発行部数3
DOI
出版物ステータス出版済み - 3 1 2019

Fingerprint

Ferritic steel
Anisotropy
Diffraction
Cold rolling
Full width at half maximum
Crystallite size
Carbon steel
Ferrite
Elastic moduli
X ray diffraction
Crystals

All Science Journal Classification (ASJC) codes

  • Mechanics of Materials
  • Mechanical Engineering
  • Metals and Alloys
  • Materials Chemistry

これを引用

Dislocation characterization by the direct-fitting/modified Williamson–Hall (DF/mWH) method in cold worked ferritic steel. / Takaki, Setsuo; Masumura, Takuro; Tsuchiyma, Toshihiro.

:: isij international, 巻 59, 番号 3, 01.03.2019, p. 567-572.

研究成果: ジャーナルへの寄稿記事

@article{89b8d4fdb5844fa6ba959d752c249d84,
title = "Dislocation characterization by the direct-fitting/modified Williamson–Hall (DF/mWH) method in cold worked ferritic steel",
abstract = "X-ray diffraction is a powerful tool for dislocation characterization, which includes evaluation of dislocation distribution, nature of dislocation, and dislocation density. In the Williamson–Hall (WH) plots, the full width at half maximum (FWHM) is plotted relative to the diffraction angle for each diffraction peak and the method corresponds to the basic approach for dislocation characterization. However, the elastic anisotropy in each crystal plane makes the analysis of WH plots difficult because elastic anisotropy also affects the FWHM of diffraction peaks. In order to correct the effect of elastic anisotropy, Ung{\'a}r developed a unique methodology by using the contrast factor C, and this is termed as the modified Williamson–Hall (mWH) method. Conversely, researchers developed a new methodology termed as the “direct-fitting (DF) method,” in which the elastic anisotropy is corrected by directly applying the diffraction Young’s modulus ratio (ω). In the DF method, a linear relation is realized in the corrected WH plots, and reliable values are obtained for the parameter α that contains information on the crystallite size. In the present study, the α-value obtained using the DF method was applied to the mWH equation, and dislocation characterization was performed in a low carbon ferritic steel (Fe-0.0056{\%}C) by cold rolling. The results indicated that increasing the extent of cold rolling decreases the screw component of dislocation, and monotonically increases the parameter φ (which contains the information of dislocation density). Additionally, the parameter A (which depends on the dislocation arrangement) was evaluated at approximately 0.50 for cold worked ferrite.",
author = "Setsuo Takaki and Takuro Masumura and Toshihiro Tsuchiyma",
year = "2019",
month = "3",
day = "1",
doi = "10.2355/isijinternational.ISIJINT-2018-623",
language = "English",
volume = "59",
pages = "567--572",
journal = "ISIJ International",
issn = "0915-1559",
publisher = "Iron and Steel Institute of Japan",
number = "3",

}

TY - JOUR

T1 - Dislocation characterization by the direct-fitting/modified Williamson–Hall (DF/mWH) method in cold worked ferritic steel

AU - Takaki, Setsuo

AU - Masumura, Takuro

AU - Tsuchiyma, Toshihiro

PY - 2019/3/1

Y1 - 2019/3/1

N2 - X-ray diffraction is a powerful tool for dislocation characterization, which includes evaluation of dislocation distribution, nature of dislocation, and dislocation density. In the Williamson–Hall (WH) plots, the full width at half maximum (FWHM) is plotted relative to the diffraction angle for each diffraction peak and the method corresponds to the basic approach for dislocation characterization. However, the elastic anisotropy in each crystal plane makes the analysis of WH plots difficult because elastic anisotropy also affects the FWHM of diffraction peaks. In order to correct the effect of elastic anisotropy, Ungár developed a unique methodology by using the contrast factor C, and this is termed as the modified Williamson–Hall (mWH) method. Conversely, researchers developed a new methodology termed as the “direct-fitting (DF) method,” in which the elastic anisotropy is corrected by directly applying the diffraction Young’s modulus ratio (ω). In the DF method, a linear relation is realized in the corrected WH plots, and reliable values are obtained for the parameter α that contains information on the crystallite size. In the present study, the α-value obtained using the DF method was applied to the mWH equation, and dislocation characterization was performed in a low carbon ferritic steel (Fe-0.0056%C) by cold rolling. The results indicated that increasing the extent of cold rolling decreases the screw component of dislocation, and monotonically increases the parameter φ (which contains the information of dislocation density). Additionally, the parameter A (which depends on the dislocation arrangement) was evaluated at approximately 0.50 for cold worked ferrite.

AB - X-ray diffraction is a powerful tool for dislocation characterization, which includes evaluation of dislocation distribution, nature of dislocation, and dislocation density. In the Williamson–Hall (WH) plots, the full width at half maximum (FWHM) is plotted relative to the diffraction angle for each diffraction peak and the method corresponds to the basic approach for dislocation characterization. However, the elastic anisotropy in each crystal plane makes the analysis of WH plots difficult because elastic anisotropy also affects the FWHM of diffraction peaks. In order to correct the effect of elastic anisotropy, Ungár developed a unique methodology by using the contrast factor C, and this is termed as the modified Williamson–Hall (mWH) method. Conversely, researchers developed a new methodology termed as the “direct-fitting (DF) method,” in which the elastic anisotropy is corrected by directly applying the diffraction Young’s modulus ratio (ω). In the DF method, a linear relation is realized in the corrected WH plots, and reliable values are obtained for the parameter α that contains information on the crystallite size. In the present study, the α-value obtained using the DF method was applied to the mWH equation, and dislocation characterization was performed in a low carbon ferritic steel (Fe-0.0056%C) by cold rolling. The results indicated that increasing the extent of cold rolling decreases the screw component of dislocation, and monotonically increases the parameter φ (which contains the information of dislocation density). Additionally, the parameter A (which depends on the dislocation arrangement) was evaluated at approximately 0.50 for cold worked ferrite.

UR - http://www.scopus.com/inward/record.url?scp=85063945725&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85063945725&partnerID=8YFLogxK

U2 - 10.2355/isijinternational.ISIJINT-2018-623

DO - 10.2355/isijinternational.ISIJINT-2018-623

M3 - Article

VL - 59

SP - 567

EP - 572

JO - ISIJ International

JF - ISIJ International

SN - 0915-1559

IS - 3

ER -