Effect of cold-working and Mo addition on creep behavior in high Mn austenitic stainless steels

Shigeru Hirata, Takanori Ito, Masatoshi Mitsuhara, Minoru Nishida

研究成果: ジャーナルへの寄稿記事

1 引用 (Scopus)

抄録

The effect of cold-working and Mo addition on creep behavior in 15Mn-17Cr-0.09C-0.39N-(0.01, 0.5, 1.0, 1.5, 2.0) Mo steels has been investigated. The steels with solution treatment at 1373 K and ones with 40% cold-rolling are subjected to a creep test at 873 K under 200-400 MPa, respectively. Time to rupture (tr) of both steels increases with increasing the Mo concentration. Since tr in the cold-rolled steels is shorter then that in solution-treated ones in a same creep condition, cold-working is suggested to be harmful for creep strength. Creep rate in a primary creep region of cold-rolled steels with more than 1.0 Mo is smaller than that for solution-treated ones because many dislocations are induced by the cold-working. This nature is advantageous as sealing materials for high temperature. Mo addition causes decreasing of minimum creep rate in the solution-treated steels. A linear relationship exists between logarithm of minimum creep rate and Mo content. In the cold-rolled steels with 0.01 Mo and 0.5 Mo, recrystallization is partially occurred during a prescribed heat treatment before the creep tests. Therefore, the creep rate is promptly accelerated. In the cold-rolled steels with more than 1.0 Mo, the suppression of recrystallization by Mo yields the small minimum creep rate and the extension of tr. Fine precipitates of Laves phase are generated in grain interior in tertiary creep region of cold-rolled steels with 1.5 and 2.0 Mo. It also contributes to the extension of tr due to the retarding effect of creep rate acceleration.

元の言語英語
ページ(範囲)51-58
ページ数8
ジャーナルTetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan
101
発行部数1
DOI
出版物ステータス出版済み - 1 1 2015

Fingerprint

cold working
Cold working
austenitic stainless steels
Austenitic stainless steel
Creep
Steel
steels
creep tests
retarding
creep strength
cold rolling
Laves phases
sealing
logarithms
precipitates
Sealants
heat treatment
Cold rolling

All Science Journal Classification (ASJC) codes

  • Condensed Matter Physics
  • Physical and Theoretical Chemistry
  • Metals and Alloys
  • Materials Chemistry

これを引用

Effect of cold-working and Mo addition on creep behavior in high Mn austenitic stainless steels. / Hirata, Shigeru; Ito, Takanori; Mitsuhara, Masatoshi; Nishida, Minoru.

:: Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan, 巻 101, 番号 1, 01.01.2015, p. 51-58.

研究成果: ジャーナルへの寄稿記事

@article{2bdcaa1859f14c18b28acaa262d9abf0,
title = "Effect of cold-working and Mo addition on creep behavior in high Mn austenitic stainless steels",
abstract = "The effect of cold-working and Mo addition on creep behavior in 15Mn-17Cr-0.09C-0.39N-(0.01, 0.5, 1.0, 1.5, 2.0) Mo steels has been investigated. The steels with solution treatment at 1373 K and ones with 40{\%} cold-rolling are subjected to a creep test at 873 K under 200-400 MPa, respectively. Time to rupture (tr) of both steels increases with increasing the Mo concentration. Since tr in the cold-rolled steels is shorter then that in solution-treated ones in a same creep condition, cold-working is suggested to be harmful for creep strength. Creep rate in a primary creep region of cold-rolled steels with more than 1.0 Mo is smaller than that for solution-treated ones because many dislocations are induced by the cold-working. This nature is advantageous as sealing materials for high temperature. Mo addition causes decreasing of minimum creep rate in the solution-treated steels. A linear relationship exists between logarithm of minimum creep rate and Mo content. In the cold-rolled steels with 0.01 Mo and 0.5 Mo, recrystallization is partially occurred during a prescribed heat treatment before the creep tests. Therefore, the creep rate is promptly accelerated. In the cold-rolled steels with more than 1.0 Mo, the suppression of recrystallization by Mo yields the small minimum creep rate and the extension of tr. Fine precipitates of Laves phase are generated in grain interior in tertiary creep region of cold-rolled steels with 1.5 and 2.0 Mo. It also contributes to the extension of tr due to the retarding effect of creep rate acceleration.",
author = "Shigeru Hirata and Takanori Ito and Masatoshi Mitsuhara and Minoru Nishida",
year = "2015",
month = "1",
day = "1",
doi = "10.2355/tetsutohagane.101.51",
language = "English",
volume = "101",
pages = "51--58",
journal = "Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan",
issn = "0021-1575",
publisher = "一般社団法人 日本鉄鋼協会",
number = "1",

}

TY - JOUR

T1 - Effect of cold-working and Mo addition on creep behavior in high Mn austenitic stainless steels

AU - Hirata, Shigeru

AU - Ito, Takanori

AU - Mitsuhara, Masatoshi

AU - Nishida, Minoru

PY - 2015/1/1

Y1 - 2015/1/1

N2 - The effect of cold-working and Mo addition on creep behavior in 15Mn-17Cr-0.09C-0.39N-(0.01, 0.5, 1.0, 1.5, 2.0) Mo steels has been investigated. The steels with solution treatment at 1373 K and ones with 40% cold-rolling are subjected to a creep test at 873 K under 200-400 MPa, respectively. Time to rupture (tr) of both steels increases with increasing the Mo concentration. Since tr in the cold-rolled steels is shorter then that in solution-treated ones in a same creep condition, cold-working is suggested to be harmful for creep strength. Creep rate in a primary creep region of cold-rolled steels with more than 1.0 Mo is smaller than that for solution-treated ones because many dislocations are induced by the cold-working. This nature is advantageous as sealing materials for high temperature. Mo addition causes decreasing of minimum creep rate in the solution-treated steels. A linear relationship exists between logarithm of minimum creep rate and Mo content. In the cold-rolled steels with 0.01 Mo and 0.5 Mo, recrystallization is partially occurred during a prescribed heat treatment before the creep tests. Therefore, the creep rate is promptly accelerated. In the cold-rolled steels with more than 1.0 Mo, the suppression of recrystallization by Mo yields the small minimum creep rate and the extension of tr. Fine precipitates of Laves phase are generated in grain interior in tertiary creep region of cold-rolled steels with 1.5 and 2.0 Mo. It also contributes to the extension of tr due to the retarding effect of creep rate acceleration.

AB - The effect of cold-working and Mo addition on creep behavior in 15Mn-17Cr-0.09C-0.39N-(0.01, 0.5, 1.0, 1.5, 2.0) Mo steels has been investigated. The steels with solution treatment at 1373 K and ones with 40% cold-rolling are subjected to a creep test at 873 K under 200-400 MPa, respectively. Time to rupture (tr) of both steels increases with increasing the Mo concentration. Since tr in the cold-rolled steels is shorter then that in solution-treated ones in a same creep condition, cold-working is suggested to be harmful for creep strength. Creep rate in a primary creep region of cold-rolled steels with more than 1.0 Mo is smaller than that for solution-treated ones because many dislocations are induced by the cold-working. This nature is advantageous as sealing materials for high temperature. Mo addition causes decreasing of minimum creep rate in the solution-treated steels. A linear relationship exists between logarithm of minimum creep rate and Mo content. In the cold-rolled steels with 0.01 Mo and 0.5 Mo, recrystallization is partially occurred during a prescribed heat treatment before the creep tests. Therefore, the creep rate is promptly accelerated. In the cold-rolled steels with more than 1.0 Mo, the suppression of recrystallization by Mo yields the small minimum creep rate and the extension of tr. Fine precipitates of Laves phase are generated in grain interior in tertiary creep region of cold-rolled steels with 1.5 and 2.0 Mo. It also contributes to the extension of tr due to the retarding effect of creep rate acceleration.

UR - http://www.scopus.com/inward/record.url?scp=84920456959&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84920456959&partnerID=8YFLogxK

U2 - 10.2355/tetsutohagane.101.51

DO - 10.2355/tetsutohagane.101.51

M3 - Article

AN - SCOPUS:84920456959

VL - 101

SP - 51

EP - 58

JO - Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan

JF - Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan

SN - 0021-1575

IS - 1

ER -