Effects of electrolysis conditions on the morphologies and corrosion resistances of polyaniline films formed on fe by electropolymerization

Hiroaki Nakano, Keichi Hayashi, Satoshi Oue, Shigeo Kobayashi

研究成果: ジャーナルへの寄稿記事

抄録

Polyaniline films were formed on an Fe substrate using the oxidative electropolymerization technique at 288 K in aqueous solutions with pH values ranging from 2 to 10 and containing aniline, p-toluenesulfonic acid and oxalic acid as supporting electrolytes. The effects of the electrolysis conditions on the morphologies and corrosion resistances of the films were subsequently investigated. Although the polyaniline films were partially formed in solutions of pH 2-4, the films completely formed and their surfaces became smooth when deposited in solutions of pH 7-10. Polyaniline films with smooth surfaces and good corrosion resistance were obtained at 8-30 A·m-2, whereas the films obtained at current densities greater than 50 A·m2 exhibited non-uniform surface morphologies and poor corrosion resistance. Films obtained at anode potentials of 0.4 V and 0.8 V vs. NHE were not formed completely, and the films formed at an anode potential of 2.0 V exhibited very rough surfaces. Films formed from a solution containing only p-toluenesulfonic acid as a supporting electrolyte exfoliated from the Fe substrate after being immersed in a 3 mass% NaCl solution for 3 h. Although the films prepared from a solution containing only oxalic acid as a supporting electrolyte exhibited good adhesion to the substrate, they contained numerous defects and pores; consequently, they improved the Fes corrosion resistance less than films deposited from a solution containing p-toluenesulfonic acid. In the case of polyaniline films formed in an electrolyte solution containing both p-toluenesulfonic acid and oxalic acid, the Fe exhibited improved corrosion resistance, and the films exhibited good adhesion to the Fe substrate.

元の言語英語
ページ(範囲)1319-1326
ページ数8
ジャーナルMaterials Transactions
57
発行部数8
DOI
出版物ステータス出版済み - 1 1 2016

Fingerprint

Electropolymerization
electrolysis
Polyaniline
Electrolysis
corrosion resistance
Corrosion resistance
Oxalic Acid
Electrolytes
acids
oxalic acid
Oxalic acid
electrolytes
Acids
Substrates
polyaniline
Anodes
adhesion
anodes
Adhesion
Aniline

All Science Journal Classification (ASJC) codes

  • Materials Science(all)
  • Condensed Matter Physics
  • Mechanics of Materials
  • Mechanical Engineering

これを引用

Effects of electrolysis conditions on the morphologies and corrosion resistances of polyaniline films formed on fe by electropolymerization. / Nakano, Hiroaki; Hayashi, Keichi; Oue, Satoshi; Kobayashi, Shigeo.

:: Materials Transactions, 巻 57, 番号 8, 01.01.2016, p. 1319-1326.

研究成果: ジャーナルへの寄稿記事

@article{d545ef976b7c436c9905f2b91d3166af,
title = "Effects of electrolysis conditions on the morphologies and corrosion resistances of polyaniline films formed on fe by electropolymerization",
abstract = "Polyaniline films were formed on an Fe substrate using the oxidative electropolymerization technique at 288 K in aqueous solutions with pH values ranging from 2 to 10 and containing aniline, p-toluenesulfonic acid and oxalic acid as supporting electrolytes. The effects of the electrolysis conditions on the morphologies and corrosion resistances of the films were subsequently investigated. Although the polyaniline films were partially formed in solutions of pH 2-4, the films completely formed and their surfaces became smooth when deposited in solutions of pH 7-10. Polyaniline films with smooth surfaces and good corrosion resistance were obtained at 8-30 A·m-2, whereas the films obtained at current densities greater than 50 A·m2 exhibited non-uniform surface morphologies and poor corrosion resistance. Films obtained at anode potentials of 0.4 V and 0.8 V vs. NHE were not formed completely, and the films formed at an anode potential of 2.0 V exhibited very rough surfaces. Films formed from a solution containing only p-toluenesulfonic acid as a supporting electrolyte exfoliated from the Fe substrate after being immersed in a 3 mass{\%} NaCl solution for 3 h. Although the films prepared from a solution containing only oxalic acid as a supporting electrolyte exhibited good adhesion to the substrate, they contained numerous defects and pores; consequently, they improved the Fes corrosion resistance less than films deposited from a solution containing p-toluenesulfonic acid. In the case of polyaniline films formed in an electrolyte solution containing both p-toluenesulfonic acid and oxalic acid, the Fe exhibited improved corrosion resistance, and the films exhibited good adhesion to the Fe substrate.",
author = "Hiroaki Nakano and Keichi Hayashi and Satoshi Oue and Shigeo Kobayashi",
year = "2016",
month = "1",
day = "1",
doi = "10.2320/matertrans.M2016083",
language = "English",
volume = "57",
pages = "1319--1326",
journal = "Materials Transactions",
issn = "0916-1821",
publisher = "The Japan Institute of Metals and Materials",
number = "8",

}

TY - JOUR

T1 - Effects of electrolysis conditions on the morphologies and corrosion resistances of polyaniline films formed on fe by electropolymerization

AU - Nakano, Hiroaki

AU - Hayashi, Keichi

AU - Oue, Satoshi

AU - Kobayashi, Shigeo

PY - 2016/1/1

Y1 - 2016/1/1

N2 - Polyaniline films were formed on an Fe substrate using the oxidative electropolymerization technique at 288 K in aqueous solutions with pH values ranging from 2 to 10 and containing aniline, p-toluenesulfonic acid and oxalic acid as supporting electrolytes. The effects of the electrolysis conditions on the morphologies and corrosion resistances of the films were subsequently investigated. Although the polyaniline films were partially formed in solutions of pH 2-4, the films completely formed and their surfaces became smooth when deposited in solutions of pH 7-10. Polyaniline films with smooth surfaces and good corrosion resistance were obtained at 8-30 A·m-2, whereas the films obtained at current densities greater than 50 A·m2 exhibited non-uniform surface morphologies and poor corrosion resistance. Films obtained at anode potentials of 0.4 V and 0.8 V vs. NHE were not formed completely, and the films formed at an anode potential of 2.0 V exhibited very rough surfaces. Films formed from a solution containing only p-toluenesulfonic acid as a supporting electrolyte exfoliated from the Fe substrate after being immersed in a 3 mass% NaCl solution for 3 h. Although the films prepared from a solution containing only oxalic acid as a supporting electrolyte exhibited good adhesion to the substrate, they contained numerous defects and pores; consequently, they improved the Fes corrosion resistance less than films deposited from a solution containing p-toluenesulfonic acid. In the case of polyaniline films formed in an electrolyte solution containing both p-toluenesulfonic acid and oxalic acid, the Fe exhibited improved corrosion resistance, and the films exhibited good adhesion to the Fe substrate.

AB - Polyaniline films were formed on an Fe substrate using the oxidative electropolymerization technique at 288 K in aqueous solutions with pH values ranging from 2 to 10 and containing aniline, p-toluenesulfonic acid and oxalic acid as supporting electrolytes. The effects of the electrolysis conditions on the morphologies and corrosion resistances of the films were subsequently investigated. Although the polyaniline films were partially formed in solutions of pH 2-4, the films completely formed and their surfaces became smooth when deposited in solutions of pH 7-10. Polyaniline films with smooth surfaces and good corrosion resistance were obtained at 8-30 A·m-2, whereas the films obtained at current densities greater than 50 A·m2 exhibited non-uniform surface morphologies and poor corrosion resistance. Films obtained at anode potentials of 0.4 V and 0.8 V vs. NHE were not formed completely, and the films formed at an anode potential of 2.0 V exhibited very rough surfaces. Films formed from a solution containing only p-toluenesulfonic acid as a supporting electrolyte exfoliated from the Fe substrate after being immersed in a 3 mass% NaCl solution for 3 h. Although the films prepared from a solution containing only oxalic acid as a supporting electrolyte exhibited good adhesion to the substrate, they contained numerous defects and pores; consequently, they improved the Fes corrosion resistance less than films deposited from a solution containing p-toluenesulfonic acid. In the case of polyaniline films formed in an electrolyte solution containing both p-toluenesulfonic acid and oxalic acid, the Fe exhibited improved corrosion resistance, and the films exhibited good adhesion to the Fe substrate.

UR - http://www.scopus.com/inward/record.url?scp=84979555066&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84979555066&partnerID=8YFLogxK

U2 - 10.2320/matertrans.M2016083

DO - 10.2320/matertrans.M2016083

M3 - Article

VL - 57

SP - 1319

EP - 1326

JO - Materials Transactions

JF - Materials Transactions

SN - 0916-1821

IS - 8

ER -