Large eddy simulation of conventional and bias flow acoustic liners

Soufiane Ramdani, Nobuhiko Yamasaki, Yuzo Inokuchi, Tatsuya Ishii

研究成果: 著書/レポートタイプへの貢献会議での発言

抄録

This study deals with the acoustic behavior of acoustic liners and the flow field around the perforated plate by solving numerically the compressible Navier-Stokes equations. The difficulty of visualizing the flow around the small holes of the plate makes the numerical simulations very attractive in order to well understand the acoustic behavior of the liner. The chosen liner was previously studied by Tam et al. [1] experimentally and using the Direct Numerical Simulation for the case of a conventional acoustic liner under normal sound wave incidence. The results obtained by Tam et al. [1] serve for the validation of the results obtained in the present research. Moreover, in this study, the focus is on the numerical simulation of the influence of bias flow on the absorption performance of a slit liner using the large eddy simulation. Two different methods are used to calculate the absorption coefficient in the computational aeroacoustics (CAA) simulation of the resonator. The first method is the transfer function method, and it simulates the impedance acoustic tube used in the experiment. The second method is the viscous dissipation method, and it calculates the power at which the acoustic energy is converted in viscous dissipation. The viscous dissipation method gives good agreement for the calculated absorption coefficients at the sound source pressure level of 150 dB. Shed vortices are developed in this case, and are considered to be the main cause of sound dissipation. The transfer function and the viscous dissipation methods used to calculate the absorption coefficients give good results for frequencies higher and equal to 2 kHz when the sound source pressure level is set to 130 dB. Only at the frequencies of 1 kHz, the obtained values are different from the values obtained by Tam et al. [1]. Shed vortices are not observed when the resonator is under only normal sound wave incidence of 130 dB. The introduction of a bias flow passing through the aperture of the resonator is investigated. The acoustic performance of the liner in this case and a comparison of the flow behavior at the aperture with a conventional liner is highlighted. When the sound pressure level is equal to 130 dB, an increase in the absorption is obtained for frequencies above the resonance frequency when the bias flow passing through the aperture is introduced. On the other hand, the absorption is reduced for the resonance frequency. However, when the SPL is equal to 150 dB, the absorption coefficient is higher near the resonance frequency, while for higher frequencies the absorption coefficient is lower.

元の言語英語
ホスト出版物のタイトルTurbomachinery
出版者American Society of Mechanical Engineers (ASME)
ISBN(電子版)9780791850800
DOI
出版物ステータス出版済み - 1 1 2017
イベントASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition, GT 2017 - Charlotte, 米国
継続期間: 6 26 20176 30 2017

出版物シリーズ

名前Proceedings of the ASME Turbo Expo
2C-2017

その他

その他ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition, GT 2017
米国
Charlotte
期間6/26/176/30/17

Fingerprint

Large eddy simulation
Acoustics
Acoustic waves
Resonators
Transfer functions
Vortex flow
Computational aeroacoustics
Perforated plates
Acoustic impedance
Computer simulation
Direct numerical simulation
Navier Stokes equations
Flow fields
Experiments

All Science Journal Classification (ASJC) codes

  • Engineering(all)

これを引用

Ramdani, S., Yamasaki, N., Inokuchi, Y., & Ishii, T. (2017). Large eddy simulation of conventional and bias flow acoustic liners. : Turbomachinery (Proceedings of the ASME Turbo Expo; 巻数 2C-2017). American Society of Mechanical Engineers (ASME). https://doi.org/10.1115/GT2017-63693

Large eddy simulation of conventional and bias flow acoustic liners. / Ramdani, Soufiane; Yamasaki, Nobuhiko; Inokuchi, Yuzo; Ishii, Tatsuya.

Turbomachinery. American Society of Mechanical Engineers (ASME), 2017. (Proceedings of the ASME Turbo Expo; 巻 2C-2017).

研究成果: 著書/レポートタイプへの貢献会議での発言

Ramdani, S, Yamasaki, N, Inokuchi, Y & Ishii, T 2017, Large eddy simulation of conventional and bias flow acoustic liners. : Turbomachinery. Proceedings of the ASME Turbo Expo, 巻. 2C-2017, American Society of Mechanical Engineers (ASME), ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition, GT 2017, Charlotte, 米国, 6/26/17. https://doi.org/10.1115/GT2017-63693
Ramdani S, Yamasaki N, Inokuchi Y, Ishii T. Large eddy simulation of conventional and bias flow acoustic liners. : Turbomachinery. American Society of Mechanical Engineers (ASME). 2017. (Proceedings of the ASME Turbo Expo). https://doi.org/10.1115/GT2017-63693
Ramdani, Soufiane ; Yamasaki, Nobuhiko ; Inokuchi, Yuzo ; Ishii, Tatsuya. / Large eddy simulation of conventional and bias flow acoustic liners. Turbomachinery. American Society of Mechanical Engineers (ASME), 2017. (Proceedings of the ASME Turbo Expo).
@inproceedings{131fa9d0256f4905ba961f3a4014c483,
title = "Large eddy simulation of conventional and bias flow acoustic liners",
abstract = "This study deals with the acoustic behavior of acoustic liners and the flow field around the perforated plate by solving numerically the compressible Navier-Stokes equations. The difficulty of visualizing the flow around the small holes of the plate makes the numerical simulations very attractive in order to well understand the acoustic behavior of the liner. The chosen liner was previously studied by Tam et al. [1] experimentally and using the Direct Numerical Simulation for the case of a conventional acoustic liner under normal sound wave incidence. The results obtained by Tam et al. [1] serve for the validation of the results obtained in the present research. Moreover, in this study, the focus is on the numerical simulation of the influence of bias flow on the absorption performance of a slit liner using the large eddy simulation. Two different methods are used to calculate the absorption coefficient in the computational aeroacoustics (CAA) simulation of the resonator. The first method is the transfer function method, and it simulates the impedance acoustic tube used in the experiment. The second method is the viscous dissipation method, and it calculates the power at which the acoustic energy is converted in viscous dissipation. The viscous dissipation method gives good agreement for the calculated absorption coefficients at the sound source pressure level of 150 dB. Shed vortices are developed in this case, and are considered to be the main cause of sound dissipation. The transfer function and the viscous dissipation methods used to calculate the absorption coefficients give good results for frequencies higher and equal to 2 kHz when the sound source pressure level is set to 130 dB. Only at the frequencies of 1 kHz, the obtained values are different from the values obtained by Tam et al. [1]. Shed vortices are not observed when the resonator is under only normal sound wave incidence of 130 dB. The introduction of a bias flow passing through the aperture of the resonator is investigated. The acoustic performance of the liner in this case and a comparison of the flow behavior at the aperture with a conventional liner is highlighted. When the sound pressure level is equal to 130 dB, an increase in the absorption is obtained for frequencies above the resonance frequency when the bias flow passing through the aperture is introduced. On the other hand, the absorption is reduced for the resonance frequency. However, when the SPL is equal to 150 dB, the absorption coefficient is higher near the resonance frequency, while for higher frequencies the absorption coefficient is lower.",
author = "Soufiane Ramdani and Nobuhiko Yamasaki and Yuzo Inokuchi and Tatsuya Ishii",
year = "2017",
month = "1",
day = "1",
doi = "10.1115/GT2017-63693",
language = "English",
series = "Proceedings of the ASME Turbo Expo",
publisher = "American Society of Mechanical Engineers (ASME)",
booktitle = "Turbomachinery",

}

TY - GEN

T1 - Large eddy simulation of conventional and bias flow acoustic liners

AU - Ramdani, Soufiane

AU - Yamasaki, Nobuhiko

AU - Inokuchi, Yuzo

AU - Ishii, Tatsuya

PY - 2017/1/1

Y1 - 2017/1/1

N2 - This study deals with the acoustic behavior of acoustic liners and the flow field around the perforated plate by solving numerically the compressible Navier-Stokes equations. The difficulty of visualizing the flow around the small holes of the plate makes the numerical simulations very attractive in order to well understand the acoustic behavior of the liner. The chosen liner was previously studied by Tam et al. [1] experimentally and using the Direct Numerical Simulation for the case of a conventional acoustic liner under normal sound wave incidence. The results obtained by Tam et al. [1] serve for the validation of the results obtained in the present research. Moreover, in this study, the focus is on the numerical simulation of the influence of bias flow on the absorption performance of a slit liner using the large eddy simulation. Two different methods are used to calculate the absorption coefficient in the computational aeroacoustics (CAA) simulation of the resonator. The first method is the transfer function method, and it simulates the impedance acoustic tube used in the experiment. The second method is the viscous dissipation method, and it calculates the power at which the acoustic energy is converted in viscous dissipation. The viscous dissipation method gives good agreement for the calculated absorption coefficients at the sound source pressure level of 150 dB. Shed vortices are developed in this case, and are considered to be the main cause of sound dissipation. The transfer function and the viscous dissipation methods used to calculate the absorption coefficients give good results for frequencies higher and equal to 2 kHz when the sound source pressure level is set to 130 dB. Only at the frequencies of 1 kHz, the obtained values are different from the values obtained by Tam et al. [1]. Shed vortices are not observed when the resonator is under only normal sound wave incidence of 130 dB. The introduction of a bias flow passing through the aperture of the resonator is investigated. The acoustic performance of the liner in this case and a comparison of the flow behavior at the aperture with a conventional liner is highlighted. When the sound pressure level is equal to 130 dB, an increase in the absorption is obtained for frequencies above the resonance frequency when the bias flow passing through the aperture is introduced. On the other hand, the absorption is reduced for the resonance frequency. However, when the SPL is equal to 150 dB, the absorption coefficient is higher near the resonance frequency, while for higher frequencies the absorption coefficient is lower.

AB - This study deals with the acoustic behavior of acoustic liners and the flow field around the perforated plate by solving numerically the compressible Navier-Stokes equations. The difficulty of visualizing the flow around the small holes of the plate makes the numerical simulations very attractive in order to well understand the acoustic behavior of the liner. The chosen liner was previously studied by Tam et al. [1] experimentally and using the Direct Numerical Simulation for the case of a conventional acoustic liner under normal sound wave incidence. The results obtained by Tam et al. [1] serve for the validation of the results obtained in the present research. Moreover, in this study, the focus is on the numerical simulation of the influence of bias flow on the absorption performance of a slit liner using the large eddy simulation. Two different methods are used to calculate the absorption coefficient in the computational aeroacoustics (CAA) simulation of the resonator. The first method is the transfer function method, and it simulates the impedance acoustic tube used in the experiment. The second method is the viscous dissipation method, and it calculates the power at which the acoustic energy is converted in viscous dissipation. The viscous dissipation method gives good agreement for the calculated absorption coefficients at the sound source pressure level of 150 dB. Shed vortices are developed in this case, and are considered to be the main cause of sound dissipation. The transfer function and the viscous dissipation methods used to calculate the absorption coefficients give good results for frequencies higher and equal to 2 kHz when the sound source pressure level is set to 130 dB. Only at the frequencies of 1 kHz, the obtained values are different from the values obtained by Tam et al. [1]. Shed vortices are not observed when the resonator is under only normal sound wave incidence of 130 dB. The introduction of a bias flow passing through the aperture of the resonator is investigated. The acoustic performance of the liner in this case and a comparison of the flow behavior at the aperture with a conventional liner is highlighted. When the sound pressure level is equal to 130 dB, an increase in the absorption is obtained for frequencies above the resonance frequency when the bias flow passing through the aperture is introduced. On the other hand, the absorption is reduced for the resonance frequency. However, when the SPL is equal to 150 dB, the absorption coefficient is higher near the resonance frequency, while for higher frequencies the absorption coefficient is lower.

UR - http://www.scopus.com/inward/record.url?scp=85028991400&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85028991400&partnerID=8YFLogxK

U2 - 10.1115/GT2017-63693

DO - 10.1115/GT2017-63693

M3 - Conference contribution

AN - SCOPUS:85028991400

T3 - Proceedings of the ASME Turbo Expo

BT - Turbomachinery

PB - American Society of Mechanical Engineers (ASME)

ER -