Notch sensitivity in fatigue limit of high strength steel

Yasuaki Hamano, Motomichi Koyama, Shigeru Hamada, Hiroshi Noguchi

研究成果: ジャーナルへの寄稿記事

抄録

The fatigue limit of a tempered martensitic steel was evaluated in specimens with stress concentration sources, which were introduced with a small drill and focused ion beam (FIB). In a previous study using ferrite-pearlite steel, the fatigue limit of a specimen with a FIB notch was almost the same as the fatigue limit of a specimen with a drill hole, and the non-propagating cracks were found around both shapes of stress concentration sources. However, the fatigue limit of the specimen with a FIB notch was about 100 MPa lower than the fatigue limit of the specimen with a drill hole in tempered martensitic steel. Additionally, the non-propagating crack was observed only in the specimen with a FIB notch. The stress concentration source shapes in both materials are the same, then the difference in fatigue limit stems from the material property. This indicates that there is applicable range where stress concentration source is regarded as a pre-crack, and the range depends on material. At first, the reason for the difference in fatigue limit was discussed in terms of the non-propagating crack. In this part, we discussed non-propagating crack phenomenon around drill hole. Secondly, the effect of hardness which caused the difference in fatigue limit was discussed by using an analytical result of Dugdale model. Finally, we inferred the notch sensitivity from the propagation by deformation at crack tip. After that, we concluded that the propagation by fracture at crack tip is also important factor in analyzing notch sensitivity.

元の言語英語
ページ(範囲)552-558
ページ数7
ジャーナルTetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan
101
発行部数10
DOI
出版物ステータス出版済み - 1 1 2015

Fingerprint

notch sensitivity
high strength steels
High strength steel
Fatigue of materials
stress concentration
Focused ion beams
cracks
Stress concentration
Cracks
notches
ion beams
Martensitic steel
crack tips
steels
Crack tips
pearlite
propagation
Pearlite
Steel
stems

All Science Journal Classification (ASJC) codes

  • Condensed Matter Physics
  • Physical and Theoretical Chemistry
  • Metals and Alloys
  • Materials Chemistry

これを引用

Notch sensitivity in fatigue limit of high strength steel. / Hamano, Yasuaki; Koyama, Motomichi; Hamada, Shigeru; Noguchi, Hiroshi.

:: Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan, 巻 101, 番号 10, 01.01.2015, p. 552-558.

研究成果: ジャーナルへの寄稿記事

@article{e69597c7e86347fdaab85400eaaf35f8,
title = "Notch sensitivity in fatigue limit of high strength steel",
abstract = "The fatigue limit of a tempered martensitic steel was evaluated in specimens with stress concentration sources, which were introduced with a small drill and focused ion beam (FIB). In a previous study using ferrite-pearlite steel, the fatigue limit of a specimen with a FIB notch was almost the same as the fatigue limit of a specimen with a drill hole, and the non-propagating cracks were found around both shapes of stress concentration sources. However, the fatigue limit of the specimen with a FIB notch was about 100 MPa lower than the fatigue limit of the specimen with a drill hole in tempered martensitic steel. Additionally, the non-propagating crack was observed only in the specimen with a FIB notch. The stress concentration source shapes in both materials are the same, then the difference in fatigue limit stems from the material property. This indicates that there is applicable range where stress concentration source is regarded as a pre-crack, and the range depends on material. At first, the reason for the difference in fatigue limit was discussed in terms of the non-propagating crack. In this part, we discussed non-propagating crack phenomenon around drill hole. Secondly, the effect of hardness which caused the difference in fatigue limit was discussed by using an analytical result of Dugdale model. Finally, we inferred the notch sensitivity from the propagation by deformation at crack tip. After that, we concluded that the propagation by fracture at crack tip is also important factor in analyzing notch sensitivity.",
author = "Yasuaki Hamano and Motomichi Koyama and Shigeru Hamada and Hiroshi Noguchi",
year = "2015",
month = "1",
day = "1",
doi = "10.2355/tetsutohagane.TETSU-2015-045",
language = "English",
volume = "101",
pages = "552--558",
journal = "Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan",
issn = "0021-1575",
publisher = "一般社団法人 日本鉄鋼協会",
number = "10",

}

TY - JOUR

T1 - Notch sensitivity in fatigue limit of high strength steel

AU - Hamano, Yasuaki

AU - Koyama, Motomichi

AU - Hamada, Shigeru

AU - Noguchi, Hiroshi

PY - 2015/1/1

Y1 - 2015/1/1

N2 - The fatigue limit of a tempered martensitic steel was evaluated in specimens with stress concentration sources, which were introduced with a small drill and focused ion beam (FIB). In a previous study using ferrite-pearlite steel, the fatigue limit of a specimen with a FIB notch was almost the same as the fatigue limit of a specimen with a drill hole, and the non-propagating cracks were found around both shapes of stress concentration sources. However, the fatigue limit of the specimen with a FIB notch was about 100 MPa lower than the fatigue limit of the specimen with a drill hole in tempered martensitic steel. Additionally, the non-propagating crack was observed only in the specimen with a FIB notch. The stress concentration source shapes in both materials are the same, then the difference in fatigue limit stems from the material property. This indicates that there is applicable range where stress concentration source is regarded as a pre-crack, and the range depends on material. At first, the reason for the difference in fatigue limit was discussed in terms of the non-propagating crack. In this part, we discussed non-propagating crack phenomenon around drill hole. Secondly, the effect of hardness which caused the difference in fatigue limit was discussed by using an analytical result of Dugdale model. Finally, we inferred the notch sensitivity from the propagation by deformation at crack tip. After that, we concluded that the propagation by fracture at crack tip is also important factor in analyzing notch sensitivity.

AB - The fatigue limit of a tempered martensitic steel was evaluated in specimens with stress concentration sources, which were introduced with a small drill and focused ion beam (FIB). In a previous study using ferrite-pearlite steel, the fatigue limit of a specimen with a FIB notch was almost the same as the fatigue limit of a specimen with a drill hole, and the non-propagating cracks were found around both shapes of stress concentration sources. However, the fatigue limit of the specimen with a FIB notch was about 100 MPa lower than the fatigue limit of the specimen with a drill hole in tempered martensitic steel. Additionally, the non-propagating crack was observed only in the specimen with a FIB notch. The stress concentration source shapes in both materials are the same, then the difference in fatigue limit stems from the material property. This indicates that there is applicable range where stress concentration source is regarded as a pre-crack, and the range depends on material. At first, the reason for the difference in fatigue limit was discussed in terms of the non-propagating crack. In this part, we discussed non-propagating crack phenomenon around drill hole. Secondly, the effect of hardness which caused the difference in fatigue limit was discussed by using an analytical result of Dugdale model. Finally, we inferred the notch sensitivity from the propagation by deformation at crack tip. After that, we concluded that the propagation by fracture at crack tip is also important factor in analyzing notch sensitivity.

UR - http://www.scopus.com/inward/record.url?scp=84943157598&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84943157598&partnerID=8YFLogxK

U2 - 10.2355/tetsutohagane.TETSU-2015-045

DO - 10.2355/tetsutohagane.TETSU-2015-045

M3 - Article

AN - SCOPUS:84943157598

VL - 101

SP - 552

EP - 558

JO - Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan

JF - Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan

SN - 0021-1575

IS - 10

ER -