Thickness Measurement of an Iron Plate Using Low-Frequency Eddy Current Testing with an HTS Coil

Teruyoshi Sasayama, Tomoki Ishida, Masaaki Matsuo, Keiji Enpuku

研究成果: ジャーナルへの寄稿記事

7 引用 (Scopus)

抄録

We applied low-frequency eddy current testing (ECT) using a high-temperature superconducting (HTS) coil in order to measure the thickness of an iron plate. Using this method, we measured changes in coil impedance when the iron plate was placed below the coil. Although low-frequency measurements were necessary to avoid the skin effect, changes in coil impedance became very small at low frequencies. For this reason, an HTS coil was used in order to sensitively measure these small changes. First, changes in the inductance L and the resistance R of the coil were measured when the iron plate was positioned 18 mm below the HTS coil, and the thickness of the plate was changed in increments from 6 to 22 mm. The results show that we were able to estimate the thickness of the plate up to 22 mm based on the changes in R when an excitation frequency of 4 Hz was used. Next, the effect of the liftoff between the iron plate and the HTS coil on the changes in L and R was studied while the liftoff was changed from 18 to 28 mm. The results show that the liftoff could be estimated from the changes in L. We were therefore able to determine the liftoff and the thickness of the iron plate by measuring changes in L and R, respectively. Results obtained from numerical simulation using the finite-element method were in agreement with the experimental results.

元の言語英語
記事番号7420626
ジャーナルIEEE Transactions on Applied Superconductivity
26
発行部数5
DOI
出版物ステータス出版済み - 8 1 2016

Fingerprint

Eddy current testing
Thickness measurement
eddy currents
coils
Iron
low frequencies
iron
Temperature
Skin effect
Inductance
impedance
Superconducting coils
frequency measurement
Finite element method
inductance
Computer simulation
finite element method

All Science Journal Classification (ASJC) codes

  • Electronic, Optical and Magnetic Materials
  • Condensed Matter Physics
  • Electrical and Electronic Engineering

これを引用

Thickness Measurement of an Iron Plate Using Low-Frequency Eddy Current Testing with an HTS Coil. / Sasayama, Teruyoshi; Ishida, Tomoki; Matsuo, Masaaki; Enpuku, Keiji.

:: IEEE Transactions on Applied Superconductivity, 巻 26, 番号 5, 7420626, 01.08.2016.

研究成果: ジャーナルへの寄稿記事

@article{59b021e2003f49e9834bae1cbea4601c,
title = "Thickness Measurement of an Iron Plate Using Low-Frequency Eddy Current Testing with an HTS Coil",
abstract = "We applied low-frequency eddy current testing (ECT) using a high-temperature superconducting (HTS) coil in order to measure the thickness of an iron plate. Using this method, we measured changes in coil impedance when the iron plate was placed below the coil. Although low-frequency measurements were necessary to avoid the skin effect, changes in coil impedance became very small at low frequencies. For this reason, an HTS coil was used in order to sensitively measure these small changes. First, changes in the inductance L and the resistance R of the coil were measured when the iron plate was positioned 18 mm below the HTS coil, and the thickness of the plate was changed in increments from 6 to 22 mm. The results show that we were able to estimate the thickness of the plate up to 22 mm based on the changes in R when an excitation frequency of 4 Hz was used. Next, the effect of the liftoff between the iron plate and the HTS coil on the changes in L and R was studied while the liftoff was changed from 18 to 28 mm. The results show that the liftoff could be estimated from the changes in L. We were therefore able to determine the liftoff and the thickness of the iron plate by measuring changes in L and R, respectively. Results obtained from numerical simulation using the finite-element method were in agreement with the experimental results.",
author = "Teruyoshi Sasayama and Tomoki Ishida and Masaaki Matsuo and Keiji Enpuku",
year = "2016",
month = "8",
day = "1",
doi = "10.1109/TASC.2016.2535366",
language = "English",
volume = "26",
journal = "IEEE Transactions on Applied Superconductivity",
issn = "1051-8223",
publisher = "Institute of Electrical and Electronics Engineers Inc.",
number = "5",

}

TY - JOUR

T1 - Thickness Measurement of an Iron Plate Using Low-Frequency Eddy Current Testing with an HTS Coil

AU - Sasayama, Teruyoshi

AU - Ishida, Tomoki

AU - Matsuo, Masaaki

AU - Enpuku, Keiji

PY - 2016/8/1

Y1 - 2016/8/1

N2 - We applied low-frequency eddy current testing (ECT) using a high-temperature superconducting (HTS) coil in order to measure the thickness of an iron plate. Using this method, we measured changes in coil impedance when the iron plate was placed below the coil. Although low-frequency measurements were necessary to avoid the skin effect, changes in coil impedance became very small at low frequencies. For this reason, an HTS coil was used in order to sensitively measure these small changes. First, changes in the inductance L and the resistance R of the coil were measured when the iron plate was positioned 18 mm below the HTS coil, and the thickness of the plate was changed in increments from 6 to 22 mm. The results show that we were able to estimate the thickness of the plate up to 22 mm based on the changes in R when an excitation frequency of 4 Hz was used. Next, the effect of the liftoff between the iron plate and the HTS coil on the changes in L and R was studied while the liftoff was changed from 18 to 28 mm. The results show that the liftoff could be estimated from the changes in L. We were therefore able to determine the liftoff and the thickness of the iron plate by measuring changes in L and R, respectively. Results obtained from numerical simulation using the finite-element method were in agreement with the experimental results.

AB - We applied low-frequency eddy current testing (ECT) using a high-temperature superconducting (HTS) coil in order to measure the thickness of an iron plate. Using this method, we measured changes in coil impedance when the iron plate was placed below the coil. Although low-frequency measurements were necessary to avoid the skin effect, changes in coil impedance became very small at low frequencies. For this reason, an HTS coil was used in order to sensitively measure these small changes. First, changes in the inductance L and the resistance R of the coil were measured when the iron plate was positioned 18 mm below the HTS coil, and the thickness of the plate was changed in increments from 6 to 22 mm. The results show that we were able to estimate the thickness of the plate up to 22 mm based on the changes in R when an excitation frequency of 4 Hz was used. Next, the effect of the liftoff between the iron plate and the HTS coil on the changes in L and R was studied while the liftoff was changed from 18 to 28 mm. The results show that the liftoff could be estimated from the changes in L. We were therefore able to determine the liftoff and the thickness of the iron plate by measuring changes in L and R, respectively. Results obtained from numerical simulation using the finite-element method were in agreement with the experimental results.

UR - http://www.scopus.com/inward/record.url?scp=84971222211&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84971222211&partnerID=8YFLogxK

U2 - 10.1109/TASC.2016.2535366

DO - 10.1109/TASC.2016.2535366

M3 - Article

AN - SCOPUS:84971222211

VL - 26

JO - IEEE Transactions on Applied Superconductivity

JF - IEEE Transactions on Applied Superconductivity

SN - 1051-8223

IS - 5

M1 - 7420626

ER -