Ultra grain refining of steels and dissolution capacity of cementite by super-heavy deformation

Hideyuki Hidaka, Yuuji Kimura, Setsuo Takaki

研究成果: ジャーナルへの寄稿記事

23 引用 (Scopus)

抄録

Mechanical milling using high energy planetary ball mill was applied to Fe-C alloy powders with (ferrite+cementite) two-phase structures to give an ultimate large strain into the powders. Dissolution behavior of cementite during mechanical milling was investigated in relation to ultra grain refining of ferrite matrix, and dissolution capacity of cementite was discussed in terms of carbon content in the powders. Ultra grain refining of ferrite matrix to about 10 nm results in full dissolution of cementite in the powders with carbon up to 2 mass% C. Most of carbon, which has been rejected from decomposed cementite, is suggested to segregate at grain boundary to form amorphous layer. Thus, it was proposed that the dissolution limit of cementite depends on both volume fraction of the grain boundary amorphous layer and carbon concentration therein. For example, as the maximum carbon content of the grain boundary amorphous layer was to be about 4.2 mass% C, the dissolution limit of cementite was estimated at 30 vol% from the mass valance for carbon content in the case ferrite grains were refined to around 10 nm. This volume fraction of cementite is just correspondent to that in Fe-2 mass%C alloy.

元の言語英語
ページ(範囲)52-58
ページ数7
ジャーナルTetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan
85
発行部数1
DOI
出版物ステータス出版済み - 1 1 1999

Fingerprint

cementite
Steel
refining
Refining
dissolving
Dissolution
Carbon
steels
Powders
Ferrite
ferrites
carbon
Grain boundaries
grain boundaries
Volume fraction
Ball mills
Mechanical alloying
Phase structure
matrices
balls

All Science Journal Classification (ASJC) codes

  • Condensed Matter Physics
  • Physical and Theoretical Chemistry
  • Metals and Alloys
  • Materials Chemistry

これを引用

Ultra grain refining of steels and dissolution capacity of cementite by super-heavy deformation. / Hidaka, Hideyuki; Kimura, Yuuji; Takaki, Setsuo.

:: Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan, 巻 85, 番号 1, 01.01.1999, p. 52-58.

研究成果: ジャーナルへの寄稿記事

@article{a64e9d710c134467a06e3262c51c488d,
title = "Ultra grain refining of steels and dissolution capacity of cementite by super-heavy deformation",
abstract = "Mechanical milling using high energy planetary ball mill was applied to Fe-C alloy powders with (ferrite+cementite) two-phase structures to give an ultimate large strain into the powders. Dissolution behavior of cementite during mechanical milling was investigated in relation to ultra grain refining of ferrite matrix, and dissolution capacity of cementite was discussed in terms of carbon content in the powders. Ultra grain refining of ferrite matrix to about 10 nm results in full dissolution of cementite in the powders with carbon up to 2 mass{\%} C. Most of carbon, which has been rejected from decomposed cementite, is suggested to segregate at grain boundary to form amorphous layer. Thus, it was proposed that the dissolution limit of cementite depends on both volume fraction of the grain boundary amorphous layer and carbon concentration therein. For example, as the maximum carbon content of the grain boundary amorphous layer was to be about 4.2 mass{\%} C, the dissolution limit of cementite was estimated at 30 vol{\%} from the mass valance for carbon content in the case ferrite grains were refined to around 10 nm. This volume fraction of cementite is just correspondent to that in Fe-2 mass{\%}C alloy.",
author = "Hideyuki Hidaka and Yuuji Kimura and Setsuo Takaki",
year = "1999",
month = "1",
day = "1",
doi = "10.2355/tetsutohagane1955.85.1_52",
language = "English",
volume = "85",
pages = "52--58",
journal = "Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan",
issn = "0021-1575",
publisher = "一般社団法人 日本鉄鋼協会",
number = "1",

}

TY - JOUR

T1 - Ultra grain refining of steels and dissolution capacity of cementite by super-heavy deformation

AU - Hidaka, Hideyuki

AU - Kimura, Yuuji

AU - Takaki, Setsuo

PY - 1999/1/1

Y1 - 1999/1/1

N2 - Mechanical milling using high energy planetary ball mill was applied to Fe-C alloy powders with (ferrite+cementite) two-phase structures to give an ultimate large strain into the powders. Dissolution behavior of cementite during mechanical milling was investigated in relation to ultra grain refining of ferrite matrix, and dissolution capacity of cementite was discussed in terms of carbon content in the powders. Ultra grain refining of ferrite matrix to about 10 nm results in full dissolution of cementite in the powders with carbon up to 2 mass% C. Most of carbon, which has been rejected from decomposed cementite, is suggested to segregate at grain boundary to form amorphous layer. Thus, it was proposed that the dissolution limit of cementite depends on both volume fraction of the grain boundary amorphous layer and carbon concentration therein. For example, as the maximum carbon content of the grain boundary amorphous layer was to be about 4.2 mass% C, the dissolution limit of cementite was estimated at 30 vol% from the mass valance for carbon content in the case ferrite grains were refined to around 10 nm. This volume fraction of cementite is just correspondent to that in Fe-2 mass%C alloy.

AB - Mechanical milling using high energy planetary ball mill was applied to Fe-C alloy powders with (ferrite+cementite) two-phase structures to give an ultimate large strain into the powders. Dissolution behavior of cementite during mechanical milling was investigated in relation to ultra grain refining of ferrite matrix, and dissolution capacity of cementite was discussed in terms of carbon content in the powders. Ultra grain refining of ferrite matrix to about 10 nm results in full dissolution of cementite in the powders with carbon up to 2 mass% C. Most of carbon, which has been rejected from decomposed cementite, is suggested to segregate at grain boundary to form amorphous layer. Thus, it was proposed that the dissolution limit of cementite depends on both volume fraction of the grain boundary amorphous layer and carbon concentration therein. For example, as the maximum carbon content of the grain boundary amorphous layer was to be about 4.2 mass% C, the dissolution limit of cementite was estimated at 30 vol% from the mass valance for carbon content in the case ferrite grains were refined to around 10 nm. This volume fraction of cementite is just correspondent to that in Fe-2 mass%C alloy.

UR - http://www.scopus.com/inward/record.url?scp=0032632225&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=0032632225&partnerID=8YFLogxK

U2 - 10.2355/tetsutohagane1955.85.1_52

DO - 10.2355/tetsutohagane1955.85.1_52

M3 - Article

AN - SCOPUS:0032632225

VL - 85

SP - 52

EP - 58

JO - Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan

JF - Tetsu-To-Hagane/Journal of the Iron and Steel Institute of Japan

SN - 0021-1575

IS - 1

ER -